Jump to content
SAU Community

Recommended Posts

hey guys. just wondering on what goes on, on resealing rear windscreen on a 32 cause the guys that did it before just took the seals out and just filled the gap in with sugaflex. now they are saying that the windscreen has to be pulled out then resealed. now i am just confused cause this was just a half finished job. could ya guys help me out here got the pic attached

thanks

post-25174-1185505002_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/178304-windscreen/
Share on other sites

yeah from da looks of things.... ur rite gonna have 2 pull it out and re-seal it....!!!!!

and da new moulding 4 da rear window is round da 500 bucks mark thats da complete seal kit genuine from nissan

im bout 2 re-do mine...!!!!

Please talk properly like your mum raised you to.

Link to comment
https://www.sau.com.au/forums/topic/178304-windscreen/#findComment-3254220
Share on other sites

You can use another type of seal, I think it is an early CommonWhore item. Not to sure on the model, I will try and find out for you, However, the fit and finish will not look as good as a Nissan jobbie, I know, I have just done front and rear screens.....

Mike

P.S

That is a shitty half job, I would tell those rude bastards to pay for the R&R of the screen, seeing as they were so quick to take your coin, but then do a sub standard job.

And If they don't like what I have to say, tell them to come talk to me direct.... I like handing out pain!

Edited by MIKE_R32_GTR
Link to comment
https://www.sau.com.au/forums/topic/178304-windscreen/#findComment-3255927
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...