Jump to content
SAU Community

Electronic Speedo Drive In A R32 Gtr Gearbox

darrinspencer
 Share

Recommended Posts

darrinspencer Grand Master

darrinspencer

Posted
Posted

I have a Stagea 4WD I have converted to manual using a R32 GTR pull gearbox which has a cable drive for speedo. The Stagea uses a electronic speedo drive.

I have searched but all tread are about r33/r34 RWD boxes in 32 GTST's

Would I have to use R33 rwd speedo drive or a r33 GTR speedo drive, or are they the same.

B0oStEr Mentor

B0oStEr

Posted
Posted
I have a Stagea 4WD I have converted to manual using a R32 GTR pull gearbox which has a cable drive for speedo. The Stagea uses a electronic speedo drive.

I have searched but all tread are about r33/r34 RWD boxes in 32 GTST's

Would I have to use R33 rwd speedo drive or a r33 GTR speedo drive, or are they the same.

I'm not sure what will do the job but the r33 rwd won't because it's too long and the teeth are cut the opposite way to what you need.

The r33gtr would be the first option I would look at.

  • 4 years later...
driftae76 Apprentice

driftae76

Posted
Posted

any updates on this? (after over 4 years :P)

I've seen a reasonably priced r32 gtr gearbox to stick in my stagea but yeah its got the cable drive also... will the stagea auto speedo drive fit the r32 box? (my guess is no, but appparently it fits into the r33 gtr box...)

Can anybody shed some light please

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...