Jump to content
SAU Community

Recommended Posts

just curious! on your boost guage what does it vacume at on idle?mine is around 18-20 psi ,which would say quiet good no?and also 18-20 wud mean no leaks at all?In old motors 18 vacume was good.

If your is different please post it :P

p.s i think my cheapo boost gauge says 13 psi when it is actually around 11?

if you have wrong reading with guages please post back also :D

Link to comment
https://www.sau.com.au/forums/topic/178421-im-curious-whats-your-vacumeon-idle/
Share on other sites

wow hold up.. 18-20psi on idle??

or am i reading your post totally wrong..

Mine is like negative 0.7 bar.. at idle.. that means its not on boost..

.7 bar is about 10 psi but that guage isnt very accurate if its the standard one?and 10 psi is weak i think?

and yes i mean 18 to 20 psi vacume at idle

Edited by cosworth1971

Its actually mmHG not psi when you are talking about the negative units on your boost guage. You can't really have negative pounds per square inch if you think about it.

But yeah mine sits on ~ -20 on idle.

Edited by Rolls

well i have tested mine so much i cna't find any leaks at all anywhere, and mine still only sits at 18" mercury at idle at 650 rpm and about 19-20 at 750 rpm.

Any common leaks to look out for, did a whole heap of test break clener, carb cleaner, smoke, pressure, all good.

Its actually mmHG not psi when you are talking about the negative units on your boost guage. You can't really have negative pounds per square inch if you think about it.

But yeah mine sits on ~ -20 on idle.

Should be IN-HG not mmHG. Well, it is on mine anyway.

Oh ok cheers! I was gonna fu**ing say, how the hell people were getting -18psi!!! Both mine and my mates sit on about -0.6, -0.7 bar.

but u earlier posted and said ur aftermarket said -10(in-hg)psi (whateva)

and tha factory boost guage is just there to look pretty IMO and wont give u a good reading

but u earlier posted and said ur aftermarket said -10(in-hg)psi (whateva)

and tha factory boost guage is just there to look pretty IMO and wont give u a good reading

Yeah aftermarket says -10psi, stock one reads about -0.7 bar which is equal to -9.8psi :thumbsup:

Nowhere near -18psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
    • Ah coolant overflow, previous discussions make way more sense now lol. 
×
×
  • Create New...