Jump to content
SAU Community

Engine Check Light Sporadically Flicking On And Off At Full Noise?!

ardie

By ardie,
in Engines & Forced Induction

 Share

Recommended Posts

ardie Experienced

ardie

Posted
Posted

Hey guys,

Well I just got my car back from RE Customs the other day and its making 280 rwkw on 16 psi (I run it on 14 daily). Last night I decided to try my high boost. the car takes off and then gate opens blah blah blah, BUT then as its getting to around 4 to 5 grand (was too busy focusing on the road) I notice the engine light flicks on and off, the flicking was similar to what happens when a light has a loose connection and whenever it moves, for that split second the connection is good again it lights up then dies again. Don’t get me wrong, I don’t think it’s a loose connection, imp just wondering what may be hurting my car. the car is stock internally with all the usual mods to support a bigger turbo (management, fuel system, exhaust, intake, afm etc) so I thought id come to the brains trust and see if you guys have any thoughts on it.

Cheers,

Ryan

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

hey mate

Sounds to me that the car is doing one of a few things

1: Knocking

2: maxing the AFM

3: maxing the injectors.

Can you do it again and this time get this data from your ECU's hand controller

1: the max knock level

2: the max injectory duty

3: the max Air flow meter voltage

then we can determin what the issue is. Is the flashing very fast or is it slow?

cheers

ardie Experienced

ardie

Posted
  • Author
Posted (edited)

Hey guys, whoa you work fast! Well the light flashed sporadically, and at a fast rate.

DAMMIT! I was hoping it wasnt knock as I mulled over it last night but given what you just said Guilt I think its knock. Im running 550cc injectors and a Q45 AFM so there shouldnt be any issues there.

I actually dont have a hand controller for the PFC as I got it as a reiculously cheap price (before they ended) minus HC. Iv been looking at getting one but I was addressing othe areas of the car before hand as i heard they went that necessary.

Thanks for the quick help boys, if you have any more advice just shoot away, last thing i want to do is melt an engine.

Cheers,

Ryan

Edited by ardie
Strik3r Experienced

Strik3r

Posted
Posted

tell your tuner to come for a spin with you and show him the problem. Sounds like they squeezed it a bit hard and it needs more fuel or less timing. They should fix it up for you on the dyno for free since you paid for a full tune.

mad082 Grand Master

mad082

Posted
Posted
If it was engine noise, you would see warning lights on low boost also, probly knock warning....

what i meant was the light is probably triggered by the knock sensor, but the knock sensor may be picking up a noise caused by something else rather than detonation. it may just be loud enough at high rpm for the knock sensor to register it. it is more than likely knock, but there is always the chance it is a false knock.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...