Jump to content
SAU Community

Oil Cooler Location

Fujiwara

By Fujiwara,
in Engines & Forced Induction

 Share

Recommended Posts

Fujiwara Proficient

Fujiwara

Posted
Posted (edited)

I have a GReddy Oil Cooler kit located BEHIND my Intercooler and in front of my radiator.

Was wondering if it would perform better if i moved it to the side of the bar (it has vents and can get all the ait it needs)

Was speaking to someone at a reputable workshop and they advised that most cars run it behind the intercoolers in the middle as the sides have disrupted air? <-- don't really know what that means but i take it that it doesn't recieve nice flowing air.

So who has their oil coolers on the side or has had them there?

Any temp differences?

If it makes any sense, i have a R34 GTT with a Nismo front bar.

Cheers

Edited by Fujiwara
Link to comment
https://www.sau.com.au/forums/topic/179349-oil-cooler-location/
Share on other sites
hecticrb25 Enthusiast

hecticrb25

Posted
Posted (edited)

Anywhere where it will get maximum airflow without hindering the performance (heating up) of any other cooling device (intercooler, radiator etc.)

If you put it out of the way of the intercooler but in the way of the radiator that would be the best spot without any major modifications imho.

Radiator should be able to cope, if it does cause an issue main way to cool your engine (i have found) isnt additional capacity in the radiator, its raising your bonnet at the back and venting at the back, works like a charm.

Edited by hecticrb25
skyguy61 Collaborator

skyguy61

Posted
Posted

Hey Dude,

I have just fitted mine to the side.. inside wheel well,i wouldnt put in front of a radiator as although you will be taking heat away from the oil you'll be adding some back into the waer via the radiator.The best position is away from the intercooler and radiator, you can hard mount it when the hoses are long, easiest way for fitment is by removing the headlight and front bar on a R33 it may be the for a 34, good luck with it. cheers

Fujiwara Proficient

Fujiwara

Posted
  • Author
Posted

of thats just great...

i can't do this myself cauz i;'ve never taken these things apart.

Nor can i fabricate brackets/mounts to fit on the site.

Have to see what some performance shops will charge me >_<

No doubt an arm and leg

GeeTR Grand Master

GeeTR

Posted
Posted
i can't do this myself cauz i;'ve never taken these things apart.

Nows the best time to start! Its just bumpers, some brackets, inner guard liner etc. Get stuck into it, just stick it all back together

Have to see what some performance shops will charge me >_<

Prolly your family's arms and legs as well. Its the labor that kills you. Search this forum for some guides and inspiration. Might not be as hard as you think. Its just large scale Meccano :D

Beer Baron Grand Master

Beer Baron

Posted
Posted

the side duct is the BEST place to put it. you will need to make a vent in the rear of the guard liner though for the air to escape, but once done you now have a much better set-up.

bombtrack Experienced

bombtrack

Posted
Posted

I'd like to mount my oil cooler kit where the stock intercooler used to be and perhaps fabricate an air guide to it. I drive an R34 and will probably do it myself. If i get it done prior to you, I will try to put together a guide.

Edit: On second thoughts, check http://www.skylinesaustralia.com/forums/in...p;hl=oil+cooler

Good guide for an R33 and should translate to R34. Great location too.

mokompri Community Regular

mokompri

Posted
Posted

before you even bother changing anything, are you actually having any oil temperature related problems ?? i would take a guess that although its not in the most ideal position, it will still be effective enough where it is.

its not a case of finding the best location gives you more power (like a fmic), but rather its purpose is to just regulate oil temps and keep them under control. if its doing that job already, then there isnt any need to move it.

GeeTR Grand Master

GeeTR

Posted
Posted
before you even bother changing anything, are you actually having any oil temperature related problems ?? i would take a guess that although its not in the most ideal position, it will still be effective enough where it is.

its not a case of finding the best location gives you more power (like a fmic), but rather its purpose is to just regulate oil temps and keep them under control. if its doing that job already, then there isnt any need to move it.

^^ pricelessly, you'll prolly find the position between i.cooler and radiator is fine.

Fujiwara Proficient

Fujiwara

Posted
  • Author
Posted

Hmm...

no problems with cooling or oil temps.

Just thought i'd move it to save trouble later on if it does occur.

But maybe you're right.

I'll keep it there and move it if i have to.

Thanks for the advice guys!

MANWHORE Grand Master

MANWHORE

Posted
Posted

My favourite spot is to have it on the side. There is room on r32s and r33s to run the lines underneath the headlight and put it on the right hand side.

I prefer this, because it has its own dedicated airflow. Also, its neater, because you don't have to run the oil lines either over or under the radiator (messy)

  • 11 months later...
E33 Enthusiast

E33

Posted
Posted

Just a heads up. I fitted a greddy oil cooler and relocator kit to a r32 gtr. Oil cooler between the ac condenser and intercooler. It's a bitch of a job to do. Will never do it again !.

Has anyone else got this set up ?

Have you taken your car to the track and did it keep your oil temperatures down ?

Cos if this setup can't take a track outing once in a while I will not be happy in relocating the mother

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...