Jump to content
SAU Community

Recommended Posts

um well im getting some adelaide input as adelaide ppl would know were to get guards flared!! and a post in general section wasnt getting much attention! so feel free to close the other one! ADELAIDE ppl r more help!!!!!!!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/180331-rim-sizes/#findComment-3280526
Share on other sites

yeh dont really wanna change the look of the guards too much! a slight flare at most! man its so friken hard finding rims! its like i want dish but dish is like too wide and too $$$$$

Wheelworx my friend............

Go down there and speak to Joe and tell him Darren sent you down there to find some dish, and just compare prices on different rims you like, They even have some second hand rims! :whistling:

Link to comment
https://www.sau.com.au/forums/topic/180331-rim-sizes/#findComment-3280654
Share on other sites

Dont paint the centres of VS-KFs black... That would be gay.

You could make those rims fit, rear would fit with a bit of a flare and run a bit of camber, fronts should be ok with a bit of camber. Around 2deg all round should see them fitting with mild flaring.

I'm assuming you're not the kind of guy into track work and handling, so running that sort of setup shouldn't bother you

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/180331-rim-sizes/#findComment-3280742
Share on other sites

I would say yes and reach outside the guard? correct me if im wrong...

Also depends on which rims...

Can you name a rim Rad?

heya bud just a note it doesnt matter wat rims they are, if its that size they will sit out no matter wat type of rim ;)

they are nice sized rims you may have to run a spacer up thr front depending on brake clearance and the possiblity of scrapin on the inner depending how low u go, would go 20mm f/g fronts (or even gtr gaurds) then roll n flared rears pure jap style yum!

Link to comment
https://www.sau.com.au/forums/topic/180331-rim-sizes/#findComment-3281559
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...