Jump to content
SAU Community

Recommended Posts

Hey in thinkin of gettin a xenon h1 conversion kit and i was wondering what would be the best colour to get.

Now i want blue, but ive checked a few different pages in google about it and some say the 6000k for instance is crystal white, and some say its blue white, and some say its aqua blue, they just all contradict eachother, so im pretty sure i want either a 6000k, 8000k or 10000k

So does anyone know more about this ?

Link to comment
https://www.sau.com.au/forums/topic/180878-xenon-colour/
Share on other sites

6000k is white, 8000k has a blue tinge, 10000k is blue, 12000k is like omg crazy purple headlights :( I does vary a little between brands but in general it goes like that. If it's a daily driven car or you actually want to be able to see something with your headlights i'd stick with the 6000k ones.

Link to comment
https://www.sau.com.au/forums/topic/180878-xenon-colour/#findComment-3287894
Share on other sites

I own 6000K globes in my car and I can say that it's got a blue tinge to it. If you want white light, go for 4300K. If you want blue, go 6000K. If you want stupid blue, go 8000K+

If I were to purchase an hid kit again, I'd go 4300K. I don't like the blue personally.

Link to comment
https://www.sau.com.au/forums/topic/180878-xenon-colour/#findComment-3289436
Share on other sites

6000k is not white, and is actually illegal.

4300k is white

6000k is blue tinge

8000k is more blue

10000k starts to go purple.

unfortunately 4300k is the only legal color due to vic roads requireing all froward facing lights to be white (excludes indicators)

each company is diff like the other guy said so yeh.......

ive got the 8000k ones and look insane, but visibility wise, i would go for the 4300k

Edited by R34NRG
Link to comment
https://www.sau.com.au/forums/topic/180878-xenon-colour/#findComment-3293647
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...