Jump to content
SAU Community

Coil Packs

i2icho

By i2icho,
in General Automotive Discussion

 Share

Recommended Posts

i2icho Enthusiast

i2icho

Posted
Posted

Hey guys please dont shoot me down, im new to the whole car scence, i own a skyline R33 '95 and my engine is misfiring occasionally above 6 psi. Ive been reading around on this Forum and have found as if i need new coil packs or need to clean them or something. The only problem being me as a Novice have No idea what so ever where to find them under the hood any help would be much appreciated, Sorry for sounding completly stupid but im still learning alot about my Skyline.

Link to comment
https://www.sau.com.au/forums/topic/181154-coil-packs/
Share on other sites
NISZILA Grand Master

NISZILA

Posted
Posted

If your going to buy new ones, look in the trader section for splitfire coilpacks. You can get them from sliding performance for a good price.

They are really easy to replace. A bit time consuming because of the intake going over the top of the engine. The top middle cover (black cover) on your engine is your coil pack cover. There are about 8 bolts to get this loose. Just use an allen key. You will need to remove the blow by hose, thats the one that connects the two sides of the top of the engine. You can then slide it out. You might also need to take off your intake pipe, but you should be able to just squeeze it past. You have now exposed your coil packs. Each has two skrews to undo and a plug from the wiring harness. When all this is loose, just pull it up. It will make a bit of a pop sound as it comes loose.

Link to comment
https://www.sau.com.au/forums/topic/181154-coil-packs/#findComment-3292081
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...