Jump to content
SAU Community

Recommended Posts

just an idea but i was thinking of getting a stock pair of 16 inch rims and putting some 4wd tyres on so i can go to a nothern surf spot. no serious 4wd just some light sand stuff and use my normal wheels for everyday driving. what size tyres could i fit on the 16 rims with no clearance problems. i have already tried some 4wd fun but with some small 4wd tyres with low pressure it would be quite capable in sand

Link to comment
https://www.sau.com.au/forums/topic/181297-stag-4wd/
Share on other sites

i dont think the attessa system would like it very much having lack of traction on the front end for long periods of time, its not really designed for that use. The clutch packs and attessa oil would heat up pretty quick i would imagine. The ocasional bit of soft sand and front wheel loss of traction is fine but non stop driving with the attessa operating the front wheels i doubt would be healthy.

thats my 2c worth :D

Link to comment
https://www.sau.com.au/forums/topic/181297-stag-4wd/#findComment-3294610
Share on other sites

i dont think the attessa system would like it very much having lack of traction on the front end for long periods of time, its not really designed for that use. The clutch packs and attessa oil would heat up pretty quick i would imagine. The ocasional bit of soft sand and front wheel loss of traction is fine but non stop driving with the attessa operating the front wheels i doubt would be healthy.

thats my 2c worth :D

+1

Tranny heat would also cause problems but thats easy to cool, the ATESSA system isn't...

Just remeber that this car was built for japanese (read icy) conditions and driving the front wheels on snow and ice doesn't drag on the power train because there is bugger all torque being transmitted. In sand there is a LOT of torque involved and thats when the heat starts to build up at the servo holding the clutch packs in.

Link to comment
https://www.sau.com.au/forums/topic/181297-stag-4wd/#findComment-3294962
Share on other sites

the aussie delivered gtr's come factory with an attessa oil cooler actually but i doubt it would be enough. The clutch packs for the front wheel drive wouldnt even pull a car off a dyno roller from my experience without smoking them badly so trying to pull a car through sand is gonna be worse imo.

Link to comment
https://www.sau.com.au/forums/topic/181297-stag-4wd/#findComment-3294969
Share on other sites

Reminds me of that old tv ad for audi quattro system - think it was the a6 quattro or allroad, or something, and the car towed a boogie boarder all over the shallows on this huge beach. - looked awesome!

Audi ended up with a serious slap on the wrist for not letting people know that they destroyed 5 cars just filming the ad! :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/181297-stag-4wd/#findComment-3299141
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...