Jump to content
SAU Community

Recommended Posts

I've read a few books about driving lately as well as gotten advice from many about improving driving skills. Everyone suggests that a key high performance driving skill is learning to heel-toe on downshifts. What I have seen mixed comments about if you should single or double clutch when you downshift. What do you guys do?

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/
Share on other sites

I only double clutch from 3rd into 2nd. I'm not sure why that is; I think its just force of habit. There's no mechanical reason for me to do so. I think even if I go from 4th to 2nd I'll still do a single clutch; definitely from 4th to 3rd is a single clutch manouvre.

I know that if I want to grab 1st from 2nd while on the move I need to double clutch; a simple heel-toe still locks me out of 1st.

Heel-toeing helps your rev match, which is good for avoiding compression locking when decellerating while not having to faff about with easing the clutch in. When you're driving close to the limits, doing stuff that stops the car from upsetting its balance is a good thing.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3299713
Share on other sites

Double clutching is one of those skills that once you have mastered just comes naturally every time that you change gears. It does put less stress on your gearbox and makes the shift smoother.

If you have a GTS-T then a simple mod is to install a GTR accelerator pedal. It is simple to install and has an extension out on the left side to make it easier to heel toe. These only cost about $20 and make heel toeing so much easier.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3299831
Share on other sites

Double clutching ie; clutch, shift to neutral, lift foot off clutch, clutch again, shift into gear?

Besides protecting your gearbox, I dont see much more point to it?

As one writer said after a while it simply becomes habit.

When you consider the correct technique for tarmac driving and cornering being to brake first then down change the double clutch down change makes no time difference whatsoever. The benefits are a smoother ride, less wear and tear on the gearbox, no compression lock. Certainly for street driving it is probably a marginal call doubling from 4th to 3rd but always 3rd to 2nd or 4th to 2nd.

In racing applications you would never think of not doubling and in fact is an important part of passing the observed driving test to gain a racing licence. After that you start to play with flat changing and left foot braking...a whole new tutorial on the left foot braking pros and cons.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3300415
Share on other sites

To be honest Im not sure myself... I think I use a mix of single and double clutching when Im heel-toe downshifting when driving spiritedly...

If its a normal downshift I will almost always double clutch. But yeah, when giving it a bit of stick you dont always have a lot of time (obviously) so sometimes I think I just single clutch?

One thing Ive noticed watching the pedal cam in Japanese clips (option, BM etc), is that a lot of drivers in those clips only single clutch when downshifting.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3300433
Share on other sites

Double clutching is one of those skills that once you have mastered just comes naturally every time that you change gears. It does put less stress on your gearbox and makes the shift smoother.

If you have a GTS-T then a simple mod is to install a GTR accelerator pedal. It is simple to install and has an extension out on the left side to make it easier to heel toe. These only cost about $20 and make heel toeing so much easier.

I've been trying to double clutch all the time on the street just to ingrain the habit, but didn't really know if there was a reason to single or double. I've had a couple of ocassion on the track where I've definately upset the balance of the car downshifting without doing it. Spun once.

I have a GTR but installed Razo pedals anyway as they are height & width adjustable so it is easier to roll over on them to blip the accelerator.

post-33908-1187664649_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3300631
Share on other sites

If you have a GTS-T then a simple mod is to install a GTR accelerator pedal. It is simple to install and has an extension out on the left side to make it easier to heel toe. These only cost about $20 and make heel toeing so much easier.

you learn something new everyday.

will be getting one soon for my GTST

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3300635
Share on other sites

The point of heel and toeing is to maintain braking while changing down ie your right foot works both the accelerator and the brake at the same time. With a syncromesh gearbox I can't see the point in double declutching, you can still match revs with speed without it. For racing it would be just too slow anyway. Well it should be :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3301307
Share on other sites

The point of heel and toeing is to maintain braking while changing down ie your right foot works both the accelerator and the brake at the same time. With a syncromesh gearbox I can't see the point in double declutching, you can still match revs with speed without it. For racing it would be just too slow anyway. Well it should be :thumbsup:

I'm with him. What's the point of doubling?

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3301587
Share on other sites

yeah in practice there's no real point double clutching, I guess in theory it saves your synchros a bit - its heal toeing/rev matching that is the important skill.

but 260DET....its not really slower, even with double clutching there are almost no places where the time to change down gears is longer than you are on the brakes anyway.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3301802
Share on other sites

I think a few people are confusing double clutching and heel-toeing.

in a synchro box there is no need to double clutch. rev matching with heel-toe is all you need to do. if you do that properly, the synchros get a harder time up-shifting on the track.

I'm with 260DET. definitely not enough time to double clutch downshift at places like Mt Cotton hillclimb. And even if there is, by the time you've done the second clutching while braking hard, your road speed will have changed so much it was all to no avail anyway.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3303090
Share on other sites

^ Exactly my thoughts.

Quiet Achiever: The benefits you stated can be achieved through rev matching alone and therefore theres no need to double clutch?

I can understand it being a habit, but besides that i stand by my point.

Link to comment
https://www.sau.com.au/forums/topic/181699-downshifting/#findComment-3303149
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...