Jump to content
SAU Community

Recommended Posts

Saturday 01 September

http://www.sdmahillclimb.com/

ENTRY FEE will be: $ 70.00 (GST incl) Late entry fee $ 20.00

Membership, entry forms and Supp Regs are on website and need to be emailed in to them by 8 p.m. 30/8/07 - I suggest you do it a day or two before this to ensure you get a spot because they do fill up. You will get 4-5 runs and a slow run before the event starts if you have never been on the track before.

MINIMUM LICENCES:

Current CAMS Level 2S Licence and club membership card are compulsory and must be produced at the Event. Membership/CAMS Forms can be downloaded, filled out and paid to SDMA on day (verify with secretary that this is still okay), but you will need to enter before then to avoid the late fee.

SCRUTINEERING will be held at: Scrutineering Bay from 7.30 a.m.

a) All vehicles must comply with Schedules A & B of the CAMS General Requirements for Automobiles (as specified in the CAMS Manual), including a fire extinguisher; blue triangle (for battery) and a secondary method for fastening the bonnet (for registered vehicles this is the secondary catch that we already have on most vehicles)

b) Maximum noise limit: 87 dba at: 30 metres. Any car found to exceed the maximum noise emission limit will be suspended from the Event until the Chief Scrutineer / Clerk of the Course is satisfied that action has been taken to bring it within the limit.

c) Competition numbers are to be positioned on both sides of the vehicle, OR at a minimum for ‘SDMA Club events’ are to be positioned on the right hand side of vehicle. SDMA may issue you with a competition numbered Card – this also indicates the running order.

d) Drivers and vehicles must be presented in a clean and tidy manner. Note: The Event will not be delayed due to late arrivals. It is the drivers’ responsibility to ensure their vehicles are scrutineered before the scheduled starting time of the Event. Drivers must attend scrutineering personally so that their driving apparel can be checked.

DRIVERS’ BRIEFING will be held: at: The Start Line at 9.00 a.m. It is compulsory for ALL drivers to attend. Scrutineering will cease whilst the drivers’ briefing is in progress.

Note: A driver “sign-on” sheet must be signed by all drivers to prove briefing attendance. Failure to sign on may result in penalties being applied by the stewards of the meeting.

The EVENT commences at: 9.30 a.m. and finishes at: 5.00 p.m.

I am here to help if you have any questions or need help with your setup.

Michele

Edited by LadyBytes
Link to comment
https://www.sau.com.au/forums/topic/181708-sdma-hillclimb-sutton-road/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...