Jump to content
SAU Community

My Bad Guys!!!

32_ENVY

By 32_ENVY,
in Victoria

 Share

Recommended Posts

32_ENVY Mentor

32_ENVY

Posted
Posted

Look, Firstly I would like to apologise for my words in my previous thread "Please Read This". It started out nicely but some ppl (unmetionables) started talking trash but thats not the point.I have done this of my own free will, I havent been pressured into doing this, I just wanna say sorry, to my friends on SAU, the moderators, Narkeh, sorry bro. Again, Sorry.

Peace:D

Link to comment
https://www.sau.com.au/forums/topic/18182-my-bad-guys/
Share on other sites
Guest terrance

Guest terrance

Posted
Posted

trash talking to INASNT isnt new, yet i feel singled out. any other trash talking was only replies to what had been said to me. but thats beside the point.

im sorry too. i wish you all long and healthy lives. <3

and theres nothing wrong with being gay. hell, even i enjoy the occasional gay porn if im in the mood. nothing beats scat porn tho. wanna see anyone?

Link to comment
https://www.sau.com.au/forums/topic/18182-my-bad-guys/#findComment-379999
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...