Jump to content
SAU Community

Recommended Posts

hi im looing at getting rid of my SAFC2 and upgrading to either of the above... what u guys recommend ? the current mods i haev and the mods im pretty sure im sticjking with.. dont think ill get anew turbo or larger injectors but *may* but i doubt it get them in the future.... so future expansion isnt a realy requirement just wanna get the most out of what i have.. currently have 182.7rwkw as dynoed a week ago with the following

R33 GTST (95 mtype)

stock EVERYTHING except:

full exhaust including high flow cat

pod filter mounted outside engine bay

FMIC (large one :O)

bleed valve at 10psi (holds very strongly for a bleed valve)

SAFC2

NGK platinum sparkies gapped to ~0.8mm

thermo fan that replaced stock clutch fan (16cm) set to ALWAYS be on

so yer what do you guys think is a better option

emanage with e-01 boost control (i also have a laptop)

or a powerfc with hand and boost controllers ? the powerfc with everything is only ~$400 more than the emanage and e-01 so i dont really care if the powerfc is better the 400 is easily justifiable... and vice versa

where to get the choice i go for tuned etc ? was thinking ice performance coz i got dynoed there and they seemed to be switched on.. unlike some other places that remain unamed have proven to be these past few months.... hehe

so yer after reading my essay please help in my choice :D:D:D cheers guys

also is it ok to block my stock BOV to getthe kool flutter noise ? or is an aftermarket BOV a better way to go for cool noises as im sick o the whoosh the stock BOV gives its just so weak lol

Out of the two, i would definately go the power fc. A much better, proven, combination.

If your reeeeally want the cop seeking attention go the atmospheric BOV. If you want to damage your turbo keep the BOV blocked and have the "cooool" fluttering noise (lol).

Otherwise be smart and stick to the plumb-back system :D.

My 2c

Alan

everyone ive spoken to today has recommended the emanage over the powerfc coz its heaps easier to tune (therefore cheaper) especially for my purposes as im not going any major upgrades.. leaving most parts stock... hmm interesting... more replies cmon peeps wanna hear what everyone has to say...

Is the e-manager a replacement ecu or a piggy-back?

Also:

Is it a direct plug-in?

Does it have the same tunning resolutions as a pfc?

Any modifications required to adapt it to you car?

Does it have the same features as a pfc? (Do you need the extra features that the pfc may offer?)

I don't know much about the e-manager, but these are the things to consider when justifing the $400 differance.

AI,

It is like a piggy back but, different. The wire in is easy and the injector harness ect. is dead simple.

Tuning resolution wise it has enough load points and then some for street use.

No mods required to adapt to car.

It has a few more features than the pfc when coupled with the E-01.

The emanage system has been used very successfuly on many a very fast vehicle. Having said that there are a few areas where Trust have had to re-develop. One area is the automatic trans nissans.

Look like the people in the know are the best to listen to, so go the e-manager :D

But i still stress, that you MUST unblock your BOV! I personally think that you mechanics advise/reasoning is dead wrong!! What do you say rev210?

yes it is unblocked at the moment and im going to keep it that way.. but my next question is if i get an aftermarket BOV... do i then disable/block my stock one ? or alwayskeep that untouched and addon my atmospheric BOV ad tune the emanage so that i dont get stalling ?

Your aftermarket BOV will replace your stock BOV. If you really must run a aftermarket BOV, i would recommend the GFB stealth. You can have them fully venting, or plumback @ the flick of a switch.

http://www.gofastbits.com.au/stealth.htm

I wouldnt bother personaly, keep the stockie. You get enough attention from the cops just driving a import, dont give them another reason to pull you over.

Cheers,

Trev

There are a few different adjustable BOV's out there.. I think an adjustable one is the best option if you must have a BOV.

I wouldnt bother personaly, keep the stockie. You get enough attention from the cops just driving a import, dont give them another reason to pull you over.

And a p plater at that :) I give him less than 2 months soon as he sticks one on.

I'd lean towards the PFC still.

Agreed that the e-manage is a good unit and has proven good results, but so has the PFC. And it really comes down to the tune.

I just like the idea of a full ECU swap, instead of something that wires into the stock ECU and fiddles with the inputs to the stock ECU.

And if you get the E-01 (for the display) your up for another $700 or what ever they are.

Good luck with what ever you get, I'm sure either of them will give you good results over the stock crappy ECU.

J

Guest INASNT

go PFC with hand controller (i got 1 sitting in my room) coz so much easier to install and u can monitor everything with the hand controller.

Also with the cop and epa situation these days if they pull your kick panel off they there is loom of wire that has been spliced into with a piggy back system u will get done, with the pfc they wont notice. Also the first thing they check now when they open your engine bay is the operation of the afm, e-manager has a map sensor doesent it?? u will get done again.

yer i spoke to ice performance today.. they recommended the powerfc and they do AWESOME work so im going to go the powerfc with hand and boost controller... as for BOVs i rekon that stealth one sounds awesome at the flick of aswitch... stealth is what im all about :P

Hahahahahaha!!

With that HUGE intercooler and the server mods to your front bar, i think stealth is out the door.

Car looks bloody great, thou i would definitely not call it stealth.

That gfb BOV, looks like a load of crap. Once the cops open the hood and see that trumpet, they will give you a canary. Same principal as a removable silencer in the mufler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...