Jump to content
SAU Community

Recommended Posts

Hey,

I want to put a FMIC on my car... 1989 R32 4 door with RB20det. Mods are 3" turboback exhuast with 2.5" split dump, turbo smart bleed valve, and a rebuilt highflow rb20det turbo.. think its rated 450hp. ATM i am running below stock boost as i dont have a boost gauge... Need to see how my mates justjap gauges look cause i cant justify $1000 on gauges for defi.

Anyways what i want to know is with the forward facing plenum i know the throttle cable will have to be shortened / lenghened. I was also thinking about getting a new throttle body.... would i need managemnt for this or it should be ok without it. Im guessing it is s my brothers s14 has a bored throttle with no management.

Anyways i have a hybrid core at home i got for free... vgc. I was thinking custom piping so i wanted the forward facing plenum to help reduce the pipe lengh to reduce lag with that turbo. It doesnt start really getting into it till around 4500rpm.

So question is what else will i have to do to all the hoses and stuff that go into my stock plenum. Can someone please post pics of their forward facing plenums, or brands of recommended plenums.

thanks

Link to comment
https://www.sau.com.au/forums/topic/183361-rb20det-forward-facing-plenum/
Share on other sites

also forgot to mention it has a walbro pump and fuel pressure regulator. All of which were on the car when i got it.

Yeah that might be true but it will help a bit and when i put everything on... i want it done properly the first time round. Dont wanna slap on a cheap kit then want something better later down track.. if you know wat i mean.

Im not to sure but i havnt seen any known brands (greddy etc.) who make forward facing plenums for rb20's but correct me anyone if im wrong. It would probably cost an arm and a leg anyways.

Another option would to have the original plenum modified. As in cut off where the inlet pipe would normally go and weld it shut. I had one on my car (still have it sitting in the shed) but had to go back to the stock one since i was defected. (supposedly it changes the numbers whilst testing for emissions).

As for the intercooler piping i personally dont think it makes a difference except maybe the looks with the extra piping needed.

obviously shorter piping is going to meen less lag. Hence why wrx has a top mount... or mad drifters have v mount... less piping meens more response... anyways.........

I dont know if the greddy plenum is forward facing or not. I have found a few but there is a pic... it looks forward facing but it sais we have these to suit... rb25, rb20, sr20, etc... so i dont know if it might be a sr20 one or what in the picture.

strich9 just did a wicked right up on a greddy style ebay plenum for a rb25. would presume fairly similar to rb20. link below

http://www.skylinesaustralia.com/forums/in...howtopic=181826

I would have thought a rechip would be higher on the list of next mods than a plenum.

especially since you have a hi-flow turbo and fuel mods and nothing controlling how it all gets mixed.

the stock plenum has been used by people making 300rwkw on the RB20

Search the NSW forum for user "Legend01" I think it is..

Also speak to user CEFFIE about re-chips.

he has/had a similar turbo to you on his RB20 and programmed his own ecu.

making 240rwkw and boost coming on ALOT earlier than what you are describing..

Your choice..

just think money would be better spent on tuning rather then "fully sick forward facing plenum bro"

when the stocker is a good unit.

upgrading to a forward facing plenum is an excellent idea IMO i'm currently doing it in my s13 Rb20 conversion.

It Shortens the IC piping required and you can shorten it even further by mounting the intercooler upside down with the outlets at the top of the core.

Have heard that it offers midrange and top end power gains (i cant confirm this as yet).

And even if you dont need the plenum (to make the power your aiming for) yet it will always be there in the future if and when you need it. And you will not need to modify your intercooler piping setup twice.

Having said this there is no point to the plenum at all if you do not use aftermarket management to take advantage of the gains the plenum can offer wether it be a rom, emanage, ems or powerfc etc ideally you will need one of these and a full retune.

The retune will be required due to the turbo upgrade regardless of the plenum to prevent it from leaning out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...