Jump to content
SAU Community

Recommended Posts

Installing a manual boost controller on an R33 (stock intercooler)

Things you need:

Pliers

Rag

Small bolt

Cable ties

WD-40 (optional)

Cotton Buds (optional)

Time: 20-30 mins

Difficulty: Easy

For this guide I used a TurboTech (TT) boost controller. I've written it for the guys i've seen posting that aren't sure what manual boost controllers do, or how to install them. It's a small job and not worth getting a mechanic to install if you have the time. There's other threads about manual boost controllers, and also about the TurboTech valve, but i've tried to be more detailed. Feel free to give comments & suggestions.

Here's how to install it:

Locate the factory soleniod on the right side of the engine bay. Here's what it looks like:

gallery_41505_11_38452.jpg

First you remove the top hose form the solenoid. It's a bit hard to budge so if you can't do it by hand grab some pliers and wrap a cloth around the hose before you start twisting it off. Once it's loose plug it with a bolt and cable tie it.

Same story with the second hose on the solenoid. Remove it, it's connected to a tee-piece. The tee sits between hoses connecting the intercooler and wastegate actuator. The TT valve will replace the tee-valve here:

gallery_41505_11_7817.jpg

There isn't much room to budge the tee out, so instead of risking a cracked or broken hose from excessive jerking just remove the hose connected to the intercooler. I sprayed a little WD-40 to make it easier, and used cotton buds to clean inside after it was off.

Now you just remove the hose from the tee-piece, remove the tee and you'll have a missing space ready for the TT.

Before you install the TT valve between the hoses adjust the bleed screw so you can blow freely into the top left barb. This keeps the boost level safe for initial adjustment.

Install the valve so it looks like this:

gallery_41505_11_35022.jpg

Make sure the clamps are fixed firmly to the hoses to prevent air leaking, or hoses popping off under pressure. Cable ties can also be used.

So that's the finished product. The boost adjustment only needs 1/4 or 1/2 turns at a time. It's very sensitive so don't go crazy tightening it. Clockwise increases boost, anti-clockwise reduces it. It's safest to test it initially 'open'.

Make sure when you take it out for a test you have a boost gauge - the valve works without it but it's just safer to recognise boost spike.

Here's a quick list of BAR=PSI conversions so you can accurately read the boost levels. As far as i know stock Skyline turbos should be kept at about an 11psi/0.75BAR limit, as a short spike at higher boost could damage the turbine.

1 BAR = 14.5 psi

0.9 BAR = 13 psi

0.83 BAR = 12 psi

0.75 BAR = 11 psi

0.69 BAR = 10 psi

0.62 BAR = 9 psi

0.55 BAR = 8 psi

0.48 BAR = 7 psi

Enjoy the extra boost!

Notes:

You should test the boost in different gears. I found that 3rd boosts a couple of pounds higher than 2nd. So try different gears throughout the rev range.

Also you'll notice a serious mid-range power increase. That's where this valve does its best work.

A final note- the hoses you connect to the TT valve have small round 'lips' inside which can cause some air restriction. Consider replacing these hoses with hollow ones for improved airflow. I haven't tried it, but i'm assuming it might bring on boost faster. nissansilvia.com has a thread talking about replacing the factory boost hoses.

Good luck! :)

Edited by R338OY

u forgot to add band aids to ur parts needed list for when u pull on the hose that joins on to the t-piece and u take all the skin off the top of ur knuckes when ur hand fies off and bashes in to the top of that radiator support. yeah it did hurt!

i havent installed a t-piece in my beast coz been using a r32 actuator,

but i was always under the impression that all that was necessary was to connect the t-piece where the factory solenoid is?

isnt it the same sorta deal? the t-piece replacing the factory solenoid in controlling the pressure?

u forgot to add band aids to ur parts needed list for when u pull on the hose that joins on to the t-piece and u take all the skin off the top of ur knuckes when ur hand fies off and bashes in to the top of that radiator support. yeah it did hurt!

Yeh, take a look at my hand in the third photo... :)

i havent installed a t-piece in my beast coz been using a r32 actuator,

but i was always under the impression that all that was necessary was to connect the t-piece where the factory solenoid is?

isnt it the same sorta deal? the t-piece replacing the factory solenoid in controlling the pressure?

Yeh spot on, the boost controller does exactly that. The spring and ball bearing inside blocks/leaks air to the wastegate actuator at a psi level you want to set, rather than the factory system (on R33's) keeping it between 5-7psi only.

I'm running about 11psi but i was told the factory turbo can take up to 14psi ( :) ), but no more.

Oh yeh i found that inside the tube from intercooler to boost controller is a small brass/copper restrictor that can be pushed out with a screwdriver. I took mine out and boost comes on stronger, earlier, though i didn't notice a massive difference.

Anyone done the same?

  • 1 month later...

i have the same boost controller which im planning on using on R32 GTR.. do i just remove the two lines going to the stock solenoid and plug it into the manual boost controller?? which line carries pressure for intercooler?? any thoughts??

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...