Jump to content
SAU Community

Recommended Posts

NEXT EVENT: Friday, November 2, from 6pm until late

-------------------

The event below has been canceled, see Here

There will be a Full Throttle Friday event held at WSID on Friday September 7th, the event is run on the same guidelines as a Wicked Wednesday off street meeting.

*Competitor gates open at 12pm with racing from 1pm

*Spectator gates open at 12:30pm

*Competitor entry fee $50

*Spectator entry fee $20

*Children under 12 are admitted FREE

It's a day event!

I might go, anyone else?

Link to comment
https://www.sau.com.au/forums/topic/183527-wsid-full-throttle-friday/
Share on other sites

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

There will be a Full Throttle Friday event held at WSID on Friday September 7th, the event is run on the same guidelines as a Wicked Wednesday off street meeting.

*Competitor gates open at 12pm with racing from 1pm

*Spectator gates open at 12:30pm

*Competitor entry fee $50

*Spectator entry fee $20

*Children under 12 are admitted FREE

It's a day event!

I might go, anyone else?

Hi there!

I get my car back from Unique Auto Sports tomorrow night, I just wanted to ask how many runs do you get and requirements for racing. Funnely enough I'v never been Before?

Joe

Hi there!

I get my car back from Unique Auto Sports tomorrow night, I just wanted to ask how many runs do you get and requirements for racing. Funnely enough I'v never been Before?

Joe

Usually on the Wednesday ones you get 4-5. Not sure about this Friday, depends on numbers I guess.

But it's pretty good since it's a public holiday and all, only time for me to hit the drags without having to take time off work.

Other conditions:

Important Items to bring:

Current Drivers Licence

Rego paper for the vehicle (if the vehicle is not registered to you,

authorisation from owner, and rego papers)

Remember - NO REGO PAPERS NO RACE

Long sleeved shirt and pants

Helmet

http://www.wsid.com.au/calendar.asp

The next one after this is:

Friday, 2 November 2007

Then

Friday, 14 December 2007

Then

Friday, 1 February 2008

Then

Friday, 29 February 2008

Etc..

Im in

With Twoogle? vrrroooom.... phhshhhh...

Thanks for that and I'll let you all know in advance if I'll come. I'v been there before to see top Fuel before but wouldn't mind maybe meeting someone to see exactly where to go. :)

:) Im a noob too lol.. Well practice makes perfect!...

I'll wear my Blue SAU T-Shirt. Seeya there!

I"M IN I"M IN!! BEEN WAITING AGES FOR THIS!!..

Just hope the weather holds up so i can set a new PB hopefully

what time does it finish btw?

Not sure but I replied to their initial email asking them when it finishes, I should know by tonite when I check email at home.

Will let ya know.. Lets hope no rain!! I want a new PB too :)

yes

w00t :D




  • Similar Content

  • Latest Posts

    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
×
×
  • Create New...