Jump to content
SAU Community

Recommended Posts

boost should not be still climbing all the way through the rev range like yours does, especially to only achieve 10spi on a standard turbo. something is wrong with the set-up for sure.

Thats what I thought! if only it was clear what the hell was wrong =(

i dont believe the standard gate should leak or bleed automatically

the actuator is std setup is always live, that is, it always see's boost pressure and only opens or starts to open at 750mhg

the auto co-incedently opens at 550mmhg so 7/5psi accordingly. the gate shouldnt open at 5psi on the manual

even the nissan service manual states for poor performance to check the actuator and use a pressure guatge to make sure it doesnt open until 750mmhg (ish).

the duty helps the controller maintain stable boost once target is reached. the duty is a ratio of opened to closed in a cycle.

so if the duty is say 80 then its 80 cycles closed, 20 cycles open. if that makes sense (in a simple way).

this stops a big boost hit and the dump, it helps maintain stable control. most ebc's can do this correctly, specially on a std turbo setup

Yeah definately looks like you have an issue...

With the EVC fitted to my car, full boost was achieved way faster than standard.

Another thing to check is the warning and boost drop settings on the EVC...

By default they are disabled, but if the tuner has set it up lower than the boost is spiking it would obviously cause a drop.

Like i mentioned before hi-boost on mine was spiking pretty high (+4 psi)

The Offset (Gain) is the main setting to ease the spiking, on high boost i wound it right down to 20% to stop the spike

Another thing to do is to RESET it and start again... my tuner had some issues with mine, so i started again :D

It is really easy to use, you just need a safe place to test it!

The intial setup is v. important because it sets the correct boost levels (Correction) so the actuator functions properly...

Michael

Yeah definately looks like you have an issue...

With the EVC fitted to my car, full boost was achieved way faster than standard.

Another thing to check is the warning and boost drop settings on the EVC...

By default they are disabled, but if the tuner has set it up lower than the boost is spiking it would obviously cause a drop.

Like i mentioned before hi-boost on mine was spiking pretty high (+4 psi)

The Offset (Gain) is the main setting to ease the spiking, on high boost i wound it right down to 20% to stop the spike

Another thing to do is to RESET it and start again... my tuner had some issues with mine, so i started again :D

It is really easy to use, you just need a safe place to test it!

The intial setup is v. important because it sets the correct boost levels (Correction) so the actuator functions properly...

Michael

Hi Michael, boost drop and warning is set at 100kpa so yeah Im nowhere near hitting that yet.

I will take the offset/gain back a little bit to prevent the spiking on the low boost setting on a cold night and see if that controls the spike.

Yeah the tuner did the initial setup with a target boost of 65kpa and correction of 100% default. 75kpa for high setting and 100% default. What are your correction settings?

Did some quick testing last nite.

In 3rd gear, it gets to 0.5 bar (about 7.5psi) pretty okay before 3000rpm

but it wont clime higher to like 0.65 bar until after 3000rpm so yeah seems laggy. It should be hitting 0.65 bar before 3000rpm I think.

I also turned the unit off, HKS manual says that turning the unit off is like running the base default boost pressure.

It hit 0.5bar again before 3000rpm and pretty much stayed there all the way to redline.

Problem is with the stock solenoid etc hooked up before the EVC install, I was getting more like 0.75 bar

So why is the controller so laggy? is it something wrong with the car or the settings?

The manual says that with the unit fitted it may lower ya base boost... Not a drama.

Mine stayed the same cos i got a full 3" exhaust done, so it balanced out the fall from the EVC install.

How different is it when its OFF compared to when its ON(in low boost mode)?

If it is very different.... it is most probably the settings!

When i switch mine off it behaves the same as before just at a lower boost level (When its ON, my Low setting is higher than base)

If adjusting setttings or reseting it fails to solve ya issue, then its is something with ya car.

Like i mentioned before, it should hit full boost relatively quicker... mine hits full boost at or just after 3K

Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...