Jump to content
SAU Community

  

77 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

lol @ ^

lets face it, the broad answer to this broad question is - wider is better.

your getting too technical.

think of it this way. these two guys had a few beers, watching ralph tv, maybe some cones, and then 1 says skinny tires are better than wide.

what do you do?

*SLAP* i'm rick james bitch

LMAO

in the dry wider tyres will grip better. in the wet if they are too wide they are more likely to aquaplane as they have to pump out more water.

more grip isn't always a good thing though. the trade off with grip is resistance. a wider tyre has more resistance, so at higher speed wider tyres can reduce acceleration and top speed.

for the drags you want as grippy (not necessarilly the widest) tyre you can get as the launch is all about grip. a supper tacky 225 will grip better than a rock hard 305. but then once you are up and going and have no problems with wheelspin you want a skinny tyre again to reduce resistance. and on the front you would want as skinny as possible to reduce rolling resistance.

for track work you want grip all round so you even up the tyre sizes since the front needs grip to stop the brakes locking (a gbetter tyre will let you brake latter than bigger breaks (unless you are unable to lock a wheel with your current brakes), as bigger brakes will make it easier to lock a brake, but better grip means the road will keep forcing the tyre to keep rotating under a higher breaking force) and give you turn in without understeer.

if you got 2 tyres of the same compound, 1 a 225 and the other a 245 then the 245 would have more grip as they are the same compound, but if you get a 235 semi slick and a 265 cheap chinese tyre the semi slick will be much better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...