Jump to content
SAU Community

Recommended Posts

hey guys,

i finally got my 33 down here to adelaide but i noticed that sometimes (80% of the time) when i accelerate from idle i.e at the lights or something. the feels like it is about to stall or something like it would in a manual car (my car being auto) only for a breif second then it moves off and goes fine...

the car in question is a 1996 Gtst series2, with no modifications and 34,000 kms on the clock, the car had not been used much before i bought it as the owner was overseas for quite some time, but it was started and driven occasionally to keep the parts going apparently,

any advice would be very helpful as i am a big newbie,

Regards,

P.A

Link to comment
https://www.sau.com.au/forums/topic/184768-r33-issue/
Share on other sites

Yea, Ive got a similar problem on my R33.

Its a auto as well. It drops the revs when i back off low revs. Its stalled in the past, so i reset the ecu. Apparently it might be the idle-motor. Might hav to get that looked at too.

Have u got a BOV installed?

Link to comment
https://www.sau.com.au/forums/topic/184768-r33-issue/#findComment-3359734
Share on other sites

+1 for the Air Flow meter.

Easy job to remove and clean even for the novice.

$5 for some carby or electrical cleaner and 10 mins work.

If that's not it, doesn't really matter but 1 thing will be eliminated.

seen this work in countless threads before though.

Link to comment
https://www.sau.com.au/forums/topic/184768-r33-issue/#findComment-3359937
Share on other sites

thanks alot for the support guys, im pretty noob so i need all the help i can get, my cars completely stock and no ChirsCross, no aftermarket BOV.

hmm can anyone point me in the right direction for a afm cleaning DIY guide

regards,

P.A

Link to comment
https://www.sau.com.au/forums/topic/184768-r33-issue/#findComment-3361397
Share on other sites

there's a DIY section full of all sorts of goodies :

http://www.skylinesaustralia.com/forums/in...hp?showforum=57 (current 1st post has alot to do with the old AFM)

And a bit more specific which may help :

http://www.skylinesaustralia.com/forums/in...p;hl=afm+clean*

Link to comment
https://www.sau.com.au/forums/topic/184768-r33-issue/#findComment-3361414
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...