Jump to content
SAU Community

Recommended Posts

  • Replies 200
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

car now has:

new windscreen. (with built in Ariel)

Full Whiteline suspension package(front and rear race sway bars,front camber kit,rear upper camber arms,rear lower tow arms,rear sub frame spacer kit)

new oil catch can modifications with sump drain back.

new water overflow tank

new front pillow ball mounts

new koyo radiator

Total cost :$3500

SELLING PRICE WILL NOW BE $38000 DOLLARS

CONSIDERING THE NEW MODIFICATIONS .

Was down at the Shift Performance track day last Friday down at Wakefield park .car ran a 1:07min on worn slicks and took out fastest AWD Turbo of the day! with new slicks and more tweaking on the suspension i can see the car dipping into the low 1:06-1:05 mark and thats with me driving :D. Also put the car on the dyno down at unigroup the night before and we realed out 392 KW on 20psi with a very rich safe tune !!

come and get your selves an awesome gtr peoples going verrryyyyy cheaaaappppppppppppp !!!!!!

hey ant - u changed your exhaust to a hks hiper...was diameter exhaust did u have before & what is it running now?

it must sound awesome without mufflers ;)

hey marko

i run the hks hiper on the street and the buddyclub on the track! it sounds fantastic with the buddy club you can hear the turbos spool like crazy !!

come on guys and gals need to move the car before i head overseas!!!! make a good offer over 35k and i will do a deal !!!

i am willing to take some parts off also!

Where about in Sydney are ya n contact no , i wanna have a look at the car Thanx

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...