Jump to content
SAU Community

Modding Up My Car At Last

B-rad33

By B-rad33,
in Victoria

 Share

Recommended Posts

B-rad33 Rising Star

B-rad33

Posted
Posted

Hey guys,

Well i thought it was time to finally do some serious mods to the car so been down and had chat and got the ball rolling.

Car should be going in hopfully next week to R.E.(current power is 193rwkw)

mods are as follows

*Garrett3076r turbo

*after market injectors

*after market pump

*ecu, either haltech or apexi fc if i can find one.

*tune etc etc

a few other bits and pieces here and there, so ill keep you updated on progess..

I would've liked to go a bigger tubro but i dont want lag..

Bradski.

Link to comment
https://www.sau.com.au/forums/topic/185332-modding-up-my-car-at-last/
Share on other sites
abu Grand Master

abu

Posted
Posted (edited)

Sounds good man, should make some good power.

Have you upgraded the clutch and gone to a FMIC?

Who are you going to get to tune it, and what sort of power you going for?

Should be able to hit 260rwkw if all goes well.

Edited by abu
abu Grand Master

abu

Posted
Posted
not sure mate,

I havent seen any other rb25's with this type of turbo, hopefully 260 but i just want a good power figure with not much lag..

Otherwise i would've gone with a GT35/40 they make really good power but they have to much lag.

I am pretty sure there is a guy on the forums running a 3071 and making 300rwkw on a internally stock RB25.

abu Grand Master

abu

Posted
Posted
1995 R33 Skyline - Series 1.5

Hybrid front mount

Power FC

Walbro fuel pump

Gt3071 interal gate with ground out R33 rear housing

Splitfire coilpacks

3" turbo back exhaust

Greddy profec spec 2 boost controller

Custom intake with pod filter

Stock afm

Stock injectors

Stock plenum

Stock exhaust manifold (except for a bit of porting done by myself)

Pretty safe tune by Mercury Motorsport

Made 234kw atw at 15psi on BP Ultimate

Full boost was seen at 3200rpm with no boost drop off at 7000rpm :yucky:

B-rad33 Rising Star

B-rad33

Posted
  • Author
Posted
check access autoworks in trade placem vermont... should have a PFC,or they can order one in. they are the only australian apexi distributor

you got there number??

cause id rather the power fc..

i dunno if they can order them in because they dont make em anymore..

Zilch* Mentor

Zilch*

Posted
Posted

Hi mate I've just had the same turbo installed on my RB25 plus a bit extra of course :mellow:

It's stock internals but everything else except the plenum is modified and it goes in to tune hopefully this week.

I'll let you know what power figure it makes, good luck with your car.

R33silverS2 Mentor

R33silverS2

Posted
Posted
Hey guys,

Well i thought it was time to finally do some serious mods to the car so been down and had chat and got the ball rolling.

Car should be going in hopfully next week to R.E.(current power is 193rwkw)

mods are as follows

*Garrett3071r turbo

*injectors

*pump

*ecu, either haltech or apexi fc if i can find one.

*tune etc etc

a few other bits and pieces here and there, so ill keep you updated on progess..

I would've liked to go a bigger tubro but i dont want lag..

Bradski.

Hey brad is the 3071r going onto the standard low manifold?

I'm looking into turbo's atm as well.

B-rad33 Rising Star

B-rad33

Posted
  • Author
Posted

well turbo has changed read as in first post, this one has a tad more power..

Im going low mount at this stage, because high will just get me into trouble. Be good for show but yeh you understand.

Im just going with advice from experts, like a said a gt35/40r(300kw and more) from what ive heard, would've been nice and made a buckert load of power but lag and prob wrecking my engine lol..

anyways things are now in action, will be finished shortly

P.S adam is teh gay.

i dont want another 50rwkw and ill get that if i add neons..

my stripe is gone too :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rear subframe stay bracket bolt removal issues

      By GTSBoy · Posted

      Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Iron Mike
      R34 GTR parts garage clean out

      By Iron Mike · Posted

      Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • waxracing
      Power steering pump r32

      By waxracing · Posted

      Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • TurboTapin
      Power steering pump r32

      By TurboTapin · Posted

      You can also remove the veins from the HICAS portion of your existing pump. 
    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana · Posted

      Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...