Jump to content
SAU Community

Recommended Posts

Please Ban the next person that asks questions about the power they got from a dyno run/tune.

the arguements about how much power it made stock or, this dyno is happy and this one is sad is getting as bad as the f*king missfire at 4500rpm on boosted R33 uleh, or flutters bro type threads.

DYNO results have the following important information.

Boost v RPM graph - to see what RPM the boost gets to max set boost level and if it stays stable etc.

A:F ratio v RPM graph - to see if it's lean or rich and at what rev range.

torque v RPM graph - to see what revs the max torque is produced to work out what revs to change at to drop back in to the meaty part of the torque curve.

how many times have people said "a dyno is a tuning tool"

never sinks in.

the forum is flooded by morons going "I only got 180rwkw with 12psi and others got 200rwkw on same psi"

BAN BAN BAN!!!

Link to comment
https://www.sau.com.au/forums/topic/185812-suggestion-to-the-moderators/
Share on other sites

You're always gunna have people less experienced than yourself asking apparent silly questions.

Part of life and this forum...and the learning experience

i plead not guilty to the above but have asked dumb stuff in the past.

I think a 'Ban' is a bit exsessive.

Just don't read it.

Every question must look a bit stupid to someone like Nismoid31 or SydneyKid but the still have the patience to give advice or point them in the right direction.

Have a beer and put your feet up :thumbsup:

Take a deeeep breath, count to 10.....(1..2...3...) ahhh, thats better

It's not the noobs.

it's people that have already been here and have read it all.

it's not the noobs that say "I have a stock skyline, can I get a tune"

that's a fair noob question.

but comparing dyno figures... and lets admit it, there is a whole shit load of it that goes on here.

BAN.

No warning.

they go to refresh, BANG.. "you have been banned for life you f*king clown." message appears.

Seat of the Pantaloons dyno figure is just as acurate as a dyno power figure.

it doesn't mean anything anyway.

Please Ban the next person that asks questions about the power they got from a dyno run/tune.

the arguements about how much power it made stock or, this dyno is happy and this one is sad is getting as bad as the f*king missfire at 4500rpm on boosted R33 uleh, or flutters bro type threads.

DYNO results have the following important information.

Boost v RPM graph - to see what RPM the boost gets to max set boost level and if it stays stable etc.

A:F ratio v RPM graph - to see if it's lean or rich and at what rev range.

torque v RPM graph - to see what revs the max torque is produced to work out what revs to change at to drop back in to the meaty part of the torque curve.

how many times have people said "a dyno is a tuning tool"

never sinks in.

the forum is flooded by morons going "I only got 180rwkw with 12psi and others got 200rwkw on same psi"

BAN BAN BAN!!!

And this children, is how to have a rant. Please pay particular attention 1) controlled use of swearing in order to maximize it's effect, 2) Use of fact's to back the initial argument/premise of the rant and 3) general reference to external threads at which the rant is aimed.

If you are having a rant, do it properly.

Nice work GTST :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...