Jump to content
SAU Community

Congrats

mike40sydney

By mike40sydney,
in Four Door Family & Wagoneers

 Share

Recommended Posts

mike40sydney Experienced

mike40sydney

Posted
  • Author
Posted
Damn str8!

..so tight, if stuck a lump of coal up there, in 2 weeks it would be a diamond.

Now, where are those scans?

that friggin tight i cant even fart sorry guys no skanna u gunna have to do wot i did and b b b b buy it.or cum ova and ill let u look for a buk

Link to comment
https://www.sau.com.au/forums/topic/187190-congrats/#findComment-3384923
Share on other sites
GoldZilla Grand Master

GoldZilla

Posted
Posted

Yep, good job to Brendan for winning the best Stagea award on the day! It was very well deserved, even though ALL of the Stageas there were well presented (except mine, I was so busy leading up to the event and helping out on the day that I didn't get time to detail or even wash my car!)

More information is here, and the article was very well written by one of our own here at SAU - Andrew "nuttsHunglow" Hearne. Quite a number of the photos were taken by SAU people as well.

Link to comment
https://www.sau.com.au/forums/topic/187190-congrats/#findComment-3386352
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...