Jump to content
SAU Community

Vibration At 100km/h


Rekin
 Share

Recommended Posts

Hey,

Ive noticed recently that when i reach 100km/h i get a huge vibration feeling throughout the car.

Cant even see through the rear view mirror as its vibrating.

Vibration can be felt through seat, gearstick etc basically the whole car.

This started to happen after a new clutch install...

Is there any chance this could be caused from the installation?

Thanks

Link to comment
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

was the flywheel machined properly? wat sort of clutch was installed? was the tailshaft done up properly? is the crossmember rubber mount done up properly? the 2 little bolts in the middle of the crossmember get forgotten about alot

Link to comment
Share on other sites

flywheel was machined by workshop

exedy heavy duty clutch with 1050kg pressure plate

Not sure about all the other questions as workshop/mechanic did the swap.

Will be going tomorrow to have a talk.

Just wanted some info from SAU before i head over there :P

Link to comment
Share on other sites

Took it to a wheel/tyre specialist, they took car for a test drive and said it wasnt wheel balance/alignment related.

Taking car back to mechanic on Friday to see if he can fix the problem, mentioned to him that it could be tailshaft and he said it could be a possibility.

thanks turboedsloth

Link to comment
Share on other sites

Yeh, i suddenly had a haggard vibration through the tailshaft of my old gts-t once at a pretty high speed, arrived at home and had a look under the car, 1 of the bolts from the bracket that bolts the tailshaft to the undercarriage had fallen out and it was hanging on a 20 degree angle, luckily no damage, evil thing

Link to comment
Share on other sites

Just got back from mechanic which double checked the tailshaft.

Everything is tight and put back the correct way (tailshaft was marked upon removal etc)

Ill book in for a 4wheel balance regardless of what the test driver said, that way i will be 1000000% sure it isnt a balance problem hehe

Link to comment
Share on other sites

  • 1 month later...

I am having the same problem with my GTR. Judging by the fact that you have a GTS-T, helps me rule out anything to do with the 4WD system.

I can tell you it isn't a wheel balance because I just had new tyres put on a week ago accompanied by a full electronic wheel balance. Everything showed 100%.

I have been told it could be the diff and so far, I am believing it. If you find out before I do what the problem is, could you please let us know?

I'm in Melbourne too and wouldn't mind meeting up to know for sure if you're problem is the exact same as mine. Sounds like it though.

Fulvio.

Link to comment
Share on other sites

PM sent, mechanic also mentioned that if a wheel balance doesnt fix the issue, then it could be the diff.

Getting camber/castor/steering rack/pineapple bushes changed as we speak along with remove/replace of a leaking power steering rack.

I will let you know if i still have a vibration problem afterwards

Link to comment
Share on other sites

hrmm

well all my suspension bushes have been replaced and a 4wheel balance & wheel alignment were done yesterday.

Vibration is still there at 100km/h

Went back to the suspension place to double check everything, and he mentioned that if the vibration is felt through the back seat, floor etc then it is a driveline vibration.

Also mentioned that it is the tailshaft as in the r32 its in 2 parts or something and happened after clutch install.

Link to comment
Share on other sites

i was having wicked bad vibes coming through around 100 cklicks for a bit...through it up on a hoist and my centre bearing may as well have been non existent... rubber had been serverly beaten... 70 bucks for a new one... good as gold now

Link to comment
Share on other sites

hey guys! i just had a similar prob, i had a gearbox replaced and the car had vibration

at over 80kph, it ended being the centre bearing was shit and the tailshaft needed to be 15mm longer. but the damage also went to the yoke seal on the gearbox.

best thing to do is take it to a driveline specialist. not including the price of the box,

that monkey mechanic who didn't check his work has cost me $1200.

could have bought a rb25det box after all,, :D

Link to comment
Share on other sites

excuse my stupidity but where is the centre bearing you speak of?

i have the same exact problem aswell, approx 105km/h and it shakes, only gets worse and you go faster too

have a feeling its the diff or gearbox as it makes a grinding noise between 2-2.5k on each gear aswell AND also can hear a bearing spinning noise (input shaft bearing?) when the clutch is not pressed and its sitting in neutral

Link to comment
Share on other sites

tek 01, the centre bearing sits roughly half was between the gear box and the diff... best way to check if it's buggered or not is to through yourself under the car...may need to be jacked up at the rear and push and pull on you tail shaft, if it moves around and clunks it's stuffed... if it stays relativly 'center' it's not you centre bearing... we have a distributer in makcay called hardy n spice.... thats where i got mine from...they seem to know there stuff

Link to comment
Share on other sites

have a feeling its the diff or gearbox as it makes a grinding noise between 2-2.5k on each gear aswell AND also can hear a bearing spinning noise (input shaft bearing?) when the clutch is not pressed and its sitting in neutral

sounds alot like your thrust bearing...is it absolutly every gear that it grinds at 2-2.5 k?........ how many K's on the car?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Stock R33 boost control, with the exhaust, and FMIC done, will boost creep. There is no tuning around it if it is the factory boost solenoid.   If it has an aftermarket electronic boost controller, the settings/mapping can be altered in it.   Oil could be anything as mentioned, however did it ever do it before you did the turbo swap? How much and how often did you drive the car before the swap?   I'm hinging on too much oil supply, or it's not draining properly.   To check, pull the air outlet off the turbo. Is it full of oil? Drop the exhaust at the turbo, does it appears to be oiled/coked? Now pull turbo and check the exhaust manifold, does it appears oiled and coked the same way?   Secondly, the PCV could even be stuffed / not functioning properly and will cause blowing of blue smoke.
    • Almost any ECU would work, from a 30 yr old PowerFC to a new Motec/Autronic. But presumably you want new middle of the road ECU, meaning that you want a Haltech or a Link, most likely. As to which model though? I dunno. I don't keep track of what they have in their current ranges. You don't want a plug in though, because plug ins can start to cause you the same wiring issues that you have to chase up with your stock ECU/loom swaps when an engine transplant is involved. If you use a Haltech (and presumably a Link) you could put the base map for the engine in and drive it around and not even need to "tune" it. It will work just fine. I can't recommend a tuner without a location (and even then I can't recommend many, being as I never use any tuners except myself and my brother-in-law). And not many tuners are happy to remote tune. Maybe they'd be happier doing it for a basically stock setup that just needs to be demonstrated to be working properly. But even then, not being able to be with the car to see what the hell is going on and sort out the inevitable problems that will result from an engine conversion done by an amateur..... unlikely to be enthusiastic about the job. And if you think that just adding 2 wires for the boost sensor is difficult - you don't want to be trying to install and set up an aftermarket ECU. You're going to have to bite down hard on something with either approach.
    • wired everything up and confirmed that the red with white stripe is indeed the fuel pump pin on this harness. 
×
×
  • Create New...