Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Madaz Grand Master

Madaz

Posted
Posted

while your doing that might as well slap a turbo on it :)

You'll need to remove the head if thats the case. Might as well throw a gasket kit at it while you're there, just to be sure. Drop the sump and replace the con bearings while you're there ... hell, re-ring it too. Check for abnormal wear and tear.

Best to spend an extra day and $300 freshening up the motor, just to be sure.

I did it will all my engines I picked up for cheap. :D

edit: oh, while the head is off, remove the valves and clean them up too.

your curve Joel from like 95 is like hold on and enjoy the ride :D

For Rad33 with his new rb25det on the way.. Get an rb30 under it. :P

RB25det vct head FTW for bottom end. :D

AL's motor is running the same GT3076 .82 on an rb30det but with a nice exhaust and inlet manifold with slightly smaller cams. The VCT has picked up some nice low end power peak power appears to be made around 7000rpm.

Now for mine.. :P 15.5psi that can be seen and the last tune at 19.5psi through the mid that tails off to 17psi causing top end to flatten out. The 2" fmic piping is causing issues up top as well as the wastegate flap being blown open.

Mine makes its peak around 6000rpm. Will play with the adj. cam gears to shift that to approx 6500rpm. :D

lol we could of told you that cars never miss behave once you get them to the mechanics - PM send about AFM's

So when the mechanics drive my car it doesnt shit itself?????????? FFS!

so where does that leave me? high and dry.

the only thing i can do is.... what for it to happen again and make sure it happens at the mechanics?

ill have to try and clean out the AFMs and check for damage.

Damo :D

sandninjas.jpg

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
    • Duncan
      Im Back baby!

      By Duncan · Posted

      wedding eh.....I seem to get to more funerals than weddings or christenings these days....
    • soviet_merlin
      Baron's R34 GT-R build thread - car in Japan for 5 years -_-

      By soviet_merlin · Posted

      Yep, cheapest options, neglected and abused. The fastest way to dislike a car is to get assigned that model by a budget rental company  
    • MBS206
      Quieter performance exhausts (or muffler add-on options)

      By MBS206 · Posted

      The noise complaint could be from absolutely anywhere, and anyone. Get it actually noise level tested to find out if you're actually over, or if you're fine. If you're over, quieten it down. If you're under, carry the test results in the car with you.
    • Matt Z
      SAU NSW x Benzin Cafe Cars & Coffee

      By Matt Z · Posted

      SAU NSW x Benzin Cafe Cars & Coffee Sunday 12th October 2025 7:30AM Meeting Benzin Cafe Meet Location: Benzin Cafe Dural RSVP: https://forms.gle/Q9TcFu9DHe4dbvtKA   *Disclaimer* One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...