Jump to content
SAU Community

Recommended Posts

while your doing that might as well slap a turbo on it :)

You'll need to remove the head if thats the case. Might as well throw a gasket kit at it while you're there, just to be sure. Drop the sump and replace the con bearings while you're there ... hell, re-ring it too. Check for abnormal wear and tear.

Best to spend an extra day and $300 freshening up the motor, just to be sure.

I did it will all my engines I picked up for cheap. :D

edit: oh, while the head is off, remove the valves and clean them up too.

your curve Joel from like 95 is like hold on and enjoy the ride :D

For Rad33 with his new rb25det on the way.. Get an rb30 under it. :P

RB25det vct head FTW for bottom end. :D

AL's motor is running the same GT3076 .82 on an rb30det but with a nice exhaust and inlet manifold with slightly smaller cams. The VCT has picked up some nice low end power peak power appears to be made around 7000rpm.

Now for mine.. :P 15.5psi that can be seen and the last tune at 19.5psi through the mid that tails off to 17psi causing top end to flatten out. The 2" fmic piping is causing issues up top as well as the wastegate flap being blown open.

Mine makes its peak around 6000rpm. Will play with the adj. cam gears to shift that to approx 6500rpm. :D

lol we could of told you that cars never miss behave once you get them to the mechanics - PM send about AFM's

So when the mechanics drive my car it doesnt shit itself?????????? FFS!

so where does that leave me? high and dry.

the only thing i can do is.... what for it to happen again and make sure it happens at the mechanics?

ill have to try and clean out the AFMs and check for damage.

Damo :D

sandninjas.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...