Jump to content
SAU Community

Recommended Posts

Straight to the point, looked (by accident) the keys in the boot of the GTR... Boot release doesnt work, so.. How to get them out, havta catch the damn bus to work cos my daily drive keys are on there also :banana:... Raa be able to 'break in' to it?

Also was lucky the boot didnt catch on fire as the rear right hand light has burnt out the left globe and wiring, hence the reason i was in the boot, put my keys down for a second and with the frustration of the rear light almost catching alight i shut the boot with them in it... What to do? Any ideas.. Stupid problem i know.

cronic a little information you may have missed

hey wat causes missfire?

coilpacks, plugs...

i have changed plugs and gapped them, and used another set of OEM coilpacks and still missfiring.

any ideas on wat else i can change? coilpack loom??

hey wat causes missfire?

coilpacks, plugs...

i have changed plugs and gapped them, and used another set of OEM coilpacks and still missfiring.

any ideas on wat else i can change? coilpack loom??

Timing could be way out? Did you plug everything in properly?

yeh timing was done when the water pump was changed 3km's ago lol...

im thinking the OEM coilpacks are not coping again...

s1 or s2

if its a s1 rb25det check the ignitor could be playing funny buggers just a suggestion.

Well the RAA dude this morning got the keys out, dont know how as i wasnt there, apparently they have a 'special way' of opening a boot lol

Anyways all good, thanks for the help people.

Now to buy a new boot lock, anyone know where i can buy one from? Thinking nisswreck or similar..

Whootage

Cleaned my car just before, the piece of shit actually tubs up alright (if you don't look at the back) :)

Also swapped the innards of the dizzy over on the poobucket daily and it drove roughly a million times better. Still got a very occaisional misfire, but it's been run down to 5/8ths of fk all petty a few times and the fuel filter has probably picked up some crap, so I've got a new one to put in when I cbf.

All in all a good days work ;)

Edited by AndrewJZX100
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...