Jump to content
SAU Community

Recommended Posts

how much? will they fit in the single DIN position under my stereo???

are they out of a r33?

They'd fit in a din sized slot easily, the main thing you have to find out is if the cables are there for them to plug in - integrated GTR gauges get their readings from the ECU, not an independant sensor. My GTR's centre gauges have two plastic plugs that clip in to the back, not sure if those plugs are there on 33's and 34's or non GTR's

-D

how much? will they fit in the single DIN position under my stereo???

are they out of a r33?

need $100ono to go towards new tyres on the front of my car as they are forked.

yes its single din , i had em in my skyline just to fill the gap between my air con and fold out screen

yes they are from an R33

343kdqh.jpg

as Dohmar said above^^^^

do u have the plugs for them???

i'm not gonr hook them up 2 my ecu, i just need the plug to have the pos/neg/illumination wires, thats all ill hook up

by the looks of it, in a GTR it must of been where the climate control was coz the right side has no corner so if i fit it under my stereo there will be a slight gap

as Dohmar said above^^^^

do u have the plugs for them???

i'm not gonr hook them up 2 my ecu, i just need the plug to have the pos/neg/illumination wires, thats all ill hook up

by the looks of it, in a GTR it must of been where the climate control was coz the right side has no corner so if i fit it under my stereo there will be a slight gap

nah dont have any plugs , just the unit its self

here is my stealth ute shes a monster now with the black sunnies and truck pipes, wonder how long till the cops pull me over bout it. :)

keep a look out for this at glandambo 4x4 event if anyone here goes to it you might see me there this year. im gunna jump the table top and land in the mudpit, hopefully land on all fours.

on another note is it illegal to have your cam gear cover off as i want to get some purdy red cam gears.

have u got a tray on the back of that? can guarantee with no tray or protection over the rear wheels you'll get looked at, but otherwise id say it'll be stealthy :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia body...
    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
×
×
  • Create New...