Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

DamageInc Grand Master

DamageInc

Posted
Posted
oh, so engine isnt as bad as you thought? I would definately get someone to open it up to verify 100% what the problem is before u contemplate fixing or selling.

its getting checked thurs/friday

still gonna sell it even if i fix it.

CRoNic... Grand Master

CRoNic...

Posted
Posted

It's hard to say, Mitch... R33 GTR's are going for roughly 24 - 28k and that's with proper GTR equipment on it (4WD, etc).

Is the engine swap engineered? Got the papers? That'll be a major selling point.

Condition of the body? Rust on chassis rails? Tyre condition? Rego'd? Is the engine bay resprayed in the same colour as the car? Air-con working? Km's (body and engine)? Gearbox good?

I'd say... 18 - 20k? But you'd get bargained down...

At the end of the day, it's still a 33 GTS-t :)

DamageInc Grand Master

DamageInc

Posted
Posted
It's hard to say, Mitch... R33 GTR's are going for roughly 24 - 28k and that's with proper GTR equipment on it (4WD, etc).

Is the engine swap engineered? Got the papers? That'll be a major selling point.

Condition of the body? Rust on chassis rails? Tyre condition? Rego'd? Is the engine bay resprayed in the same colour as the car? Air-con working? Km's (body and engine)? Gearbox good?

I'd say... 18 - 20k? But you'd get bargained down...

At the end of the day, it's still a 33 GTS-t :)

its basically a road registered , track going skyline .

if you wanna discuss anything more pm me , dont really want the wrong eyes getting hold of the details of my car :)

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...