Jump to content
SAU Community

Recommended Posts

yes thats the delimer im in, all cash has been thrown at home loan. preventing me from buying another car.

i need to be sensible :) there's only 1 carport at my house and thats got GTR written all over it.

its justafiable a normal person needs 3 cars right? 1 for when it rains 1 to drive to work when it dosnt rain and 1 for weekend trips :D

Edited by Inline 6

i cant get another project until i get a shed up...my mate has a datto 1200 he wont sell me until i get a shed.....now i just need my "minister of finances" to let me do it....my brother in law is a sparky , so wiring wont be a problem...i helped concrete my uncles burnout pad...so concreting wont be a problem....gotta save money everywhere....this week i have to fix a leak on my eldest's motorbike as well....it never ends

Does anyone know any cheap companies that do...

Fencing

Driveways/Concrete or Pavers

House perimiter concrete or pavers

Flooring (Tiles/Carpets etc)

I can do it through my builder but he said its cheaper not to....

do the paving and carpeting yaself is 1 option :D

That was a joke yeah?

I dont see that working out haha

I cant get the loan until I have quotes for that stuff... well thats if I get pre approved... they havn't got back to me yet...

i got my loan without qoutes for it, hmmmzzz although i had a huge deposit they prob didnt care so much cause they gonna get their cash back no matter what.

pavings not that hard i hear, you may break a nail or 2 though :D

I dont have any nails to break at the moment!

I dunno why... its a Homestart condition.

I can always get quotes and not use them, do it myself over time... if they dont check.

I dont have any nails to break at the moment!

I dunno why... its a Homestart condition.

I can always get quotes and not use them, do it myself over time... if they dont check.

I think a place like Homestart would only instruct the bank to release the funds to the company/tradesperson carrying out the work.

Penny, go to the Home Centre corner of Anzac Hwy and South Road if you can, and get some ideas on who to employ for those jobs. Even the centres that sell the materials (paving etc) will have contractors they can get to do the work. And it should be cheaper than the builder (Homestart) getting it done for you.

I'm in the middle of building my own extension. Doing all the work (99.9%) of it myself and its not easy. Paving would be a breeze in comparison. But I study construction management, so I gotta know this shit. :(

Even better for you ... stand out the front of my TAFE college and look pretty and sucker some of the studying tradies to do the work for you :D

The Design and Construction Management course has two sides: the designers/drafters (like me) and the builders (them), and we like to give them crap :D

Edited by RubyRS4

I can lend you 1 of my skirts if you need penny rofl warning may look like a tshirt but i assure u its a skirt.

might be cause yeah i amended it after i got approval, or might be the builders and lenders im through know im friends with their biggest client :D

Edited by Inline 6
I think a place like Homestart would only instruct the bank to release the funds to the company/tradesperson carrying out the work.

Penny, go to the Home Centre corner of Anzac Hwy and South Road if you can, and get some ideas on who to employ for those jobs. Even the centres that sell the materials (paving etc) will have contractors they can get to do the work. And it should be cheaper than the builder (Homestart) getting it done for you.

I'm in the middle of building my own extension. Doing all the work (99.9%) of it myself and its not easy. Paving would be a breeze in comparison. But I study construction management, so I gotta know this shit. :P

Even better for you ... stand out the front of my TAFE college and look pretty and sucker some of the studying tradies to do the work for you :D

The Design and Construction Management course has two sides: the designers/drafters (like me) and the builders (them), and we like to give them crap :(

Haha well that could work!! Where is your TAFE? Lol

I'll have to get to that Home Centre and have a look this weekend I think.

I have emailed a few places for rough quotes, one of them was more expensive then the builder!

Lucky you being able to do it all yourself, I struggled making the barbie fold and fun house. :D

I could probably build a dog kennel. Thats about it. Mind you I have never tried...

so whats the mates rates ruby :(

To design you a building in accordance with all Australian Standards and Council codes ... I wouldn't even hazard a guess for a fixed fee ... but generally $60 per hour is the norm and there are ALOT of hours involved. And thats just the designing stage.

I'm amending the drawings to my house extension every week or so. Its not as simple as drawing the house you want.

Lesson in one storey building design, so listen up ... :D

The building must be designed for the use of standard brickwork, so the dimensions of the house are determined by the brick course. Openings for windows and doors etc must also meet design consideration of brickwork. There are set dimensions for wall construction and cavities. Cut and fill for the buidling footprint on the site. AS for timber type and strength for roof loads. Council design techniques to be considered for energy efficient homes. Consideration of open space and floor area ratios. Overlooking and overshadowing issues. And so on and so forth. Thats only the tip of the iceberg. I'm designing a house in the south-east corner of the city and its a nightmare because of the narrow dimensions and Council rules!

For the most part, I mainly design road networks in dwelling in-fill areas/residential growth areas. And also site plans for extensions and redevelopments. I'm in the process of applying for an ABN and business name to do some consulting/drafting on the side.

I'd like to stick with the design side of things and leave the labour to other poor bastards :D

That sounds crazy hard. :D

They drum it into you hard enough. Things like this you need to know. Otherwise buildings fall down and people die ... pretty much.

For instance, my floors for my extension are made of timber, suspended over natural ground level. Now I need minimum 100mm clearance from ground to any timber member of the floor. If I use the narrowest timber, I could get away with meeting my existing floor level of 300mm above ground. Well I lose 100mm already from the clearance rule, so that leaves 200mm. Due to the length of my floor bearers of some 7.8m in continuous span, I need 190x45mm timber for my bearers. On top of that goes the 190x35mm floor joists. Well 100+190+190=480, which will be 180mm above my existing floor level of the existing building (not including the 22mm floor boards!). However, I can run the floor joists in single span (not continuous span) between (not on top of) the floor bearers = 100+190=290 which means it meets my current floor level. However, the single spans at (still) such a long span means I need to run them every 450mm, not 600mm to keep the 190x35 profile. Or 600mm at 190x45 profile.

So economically:

7.8m / 0.6 (600mm) = (13+1) 14 rows of joists

therefore 190x45 = 8,500 unit x 14 = 119,700

7.8m / 0.45 (450mm) = (17+1) 18 rows of joists

therefore 190x35 = 6,650 units x 18 = 119,700

Economically they will be identical in cost. So I might as well order more 190x45, rather than a bit of 190x35 and a bit of 190x45.

Lost yet??? And thats only the floor!!! I have to do this shit every week! :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...