Jump to content
SAU Community

R33 Performance Parts Massive Price Drop Avcr Available

MrMike
 Share

Recommended Posts

MrMike Collaborator

MrMike

Posted
Posted (edited)

Hey guys change of plans all of this stuff is still in the car so will need a little time to get it all out.

XFORCE BellMouth SS Dump/Front............$230.....$300 with highflow cat

APEXI AVCR In box with stand Great condition $370.....back up for sale......Thanks for F*^king me around ghostflamer33

XFORCE High Flow CAT,............$120....$300 with Dump/Front

Tech Edge WBO2 controller................240

Nismo FPR (i believe its nismo)...........$90

Link GTS ECU Full Plug in..with Hand controller and PC Tuning software...everything needed (perfect for automatic).......$700....(this is cheap)

Everything Excellent Condition

Located in Sydney.......

post-18765-1192061782_thumb.jpg

post-18765-1192238127_thumb.jpg

post-18765-1192238162_thumb.jpg

post-18765-1192238190_thumb.jpg

post-18765-1192238238_thumb.jpg

Edited by MrMike
abu Grand Master

abu

Posted
Posted
Its a 3inch Cat......Been in the car for about 2months.

It is a dump/front pipe. At this stage pickup only on the heavier items.

Abu how did you go with the clarion head unit...?

CLARION head unit is finally sold man, after a bit of stuffing around.

Will get back to you about the CAT :rolleyes:

Thanks,

Abu

MrMike Collaborator

MrMike

Posted
  • Author
Posted

its not that one.......you take the circuit board out of your old computer and put the link one in. map sensor wires straight into the MAF wiring.......very simple install.....great computer, Has closed loop lamda.

Selling because i am putting the car back to stock and selling that aswell.

aaron_25t Collaborator

aaron_25t

Posted
Posted

PM sent

its not that one.......you take the circuit board out of your old computer and put the link one in. map sensor wires straight into the MAF wiring.......very simple install.....great computer, Has closed loop lamda.

Selling because i am putting the car back to stock and selling that aswell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • MBS206
      R32 update from 1990's spec.

      By MBS206 · Posted

      With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • joshuaho96
      RB26DETT Sketchy boost mod?

      By joshuaho96 · Posted

      This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...