Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

ok i changed the ecu still nothing its still a s1 ecu

with my motor i stripped all s2 electronic parts off it and put all my s1 parts on it

im pretty sure the motor was a s1 out of a auto stagea i just have no power at all nohting to dash lighst nothin ??

well thats what im trying to find is there any main power wire

its hard to find thinsga cause i have a greddy plenum on it now also

when i was charging the battery from under the boonet the dash lights came up with a real slow flash and a beep like when u leave your door open ???

but now there is nothing when i turn the key i get nothing

i cant see any more wires at all on both sides worst thing is i live in a country two 10 hours from sydney 6 form melb and 4 form adelaide so yer ................rooted??

sounds like a dead battery. You shouldnt be charging the battery with it still connected to the car.

Pull it out and give it a decent deep cycle charge (ie leave it on charge for at least 24hrs). Battery chargers charge at a very low ampage so it takes a while.

If its not that the battery its a main power connection thats not connected properly. Make sure your getting a good contact at the major areas like the battery terminals and the earth lines to the engine itself.

if you put the terminals on backwards i would say the main realy woulda blown but as long as you havent done that it should be fine, its designed to jump start the car so i couldnt do any damage just wont charge the battery effectivly

as mentioned b4 i think its cos you have a motor/ecu mismatch. the series 1 stageas were based on the series 2 r33 (rb25) and series 2 stags on the r34 (rb25neo). so if like you said you stripped all the wiring off and are trying to use the wiring from a series 1 r33 rb25 it wont work. you dont have an ignitor. find a series 2 r33 or a series 1 stagea ecu and try that

ill try a r33 series two ecu but what about my ignitor how do i get passed that ?? i have one and if i put a series two ecu in they dont have a sepreate ignitor

i still have the coil packs from the series 2 so i can put them in

i dont think it is the battery cause i had a jumper pack on and it still didnt go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...