Jump to content
SAU Community

Recommended Posts

really how did u know Ed? ur eyes been sneaking have they? fag(no offence to other gay people)

dont worry smokey wont get offended, hes used to it!

hahaha

Ill come visit ya tonight mass, wat time u there till

1 nutta

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

bad luck mass, hope u can garage the car soon driveways suck! I wouldnt have ever considerd buying the cars ive had if i didnt have my garage.. But thats no excuse some people are f*ck heads thats for sure try living in guildford...

im here till 11ish...

just look for the beast out front, if its not there then im gone!!! but then again the lights will be off hahahaha

sweet im meant to be here till 12 tonight but will prob jet eariler... about to get the Feed in for Californication Episode 9!!! red hot!!

bad luck mass, hope u can garage the car soon driveways suck! I wouldnt have ever considerd buying the cars ive had if i didnt have my garage.. But thats no excuse some people are f*ck heads thats for sure try living in guildford...

yeh it does, i mean the car is under ea car port, below road level, its secure with a car parked behind and a big gate. so its not too bad for now... stupid gronks... i dunno

nah, no way did someone steal one nut.

it either came loose or the stud has broken off.

when you say you checked they were tight, what was the torque wrench set to? What are the other 4 nuts on that wheel tightened to atm?

well i only torqued them up by hand, i dont have a torque rench... they were all firm and didnt need tightening. the stud isnt broken and there are no signs of metal filings, so it wasnt forced off or anything... as for coming loose i really really doubt it, i mean i checked them on sat wen i washed the car, it was only driven once over the weekend for like 30mins, and thats it. no chance of that...

That really sucks, man...

I'm considering putting some wheels on Teh Wagon, but:

1. I like to roll stealth; and

2. I'm worried about this happening to me too.

I don't use my car a lot, but by the same token it's not a garage queen. If I have to go out, I use it. I'm pretty careful about where I park, but you can't always park exactly where you want, can you? And to think that this could have happened when you have your car parked AT HOME really sucks.

That really sucks, man...

I'm considering putting some wheels on Teh Wagon, but:

1. I like to roll stealth; and

2. I'm worried about this happening to me too.

I don't use my car a lot, but by the same token it's not a garage queen. If I have to go out, I use it. I'm pretty careful about where I park, but you can't always park exactly where you want, can you? And to think that this could have happened when you have your car parked AT HOME really sucks.

Yeh same with me man, i try to park it in places were its visible, as in most people can see it so no1 really has the chance to breakin, i mean i wudnt be able to leave it isolated in a back street for longer then 10-15mins hahaha it gets annoying but meh wat do u do? I thought of this before i bought it, but i mean i really wanted a 34GTR so i said who cares i can deal with it... its hard tho..

Sorry to hear that Mass Iv!!

I'm looking out for my rims!! they costed $2000 ! so I'm heaps worried :)

i hate thieves... :yes:

yeh i know the feeling, i mean my rims are worth at least $3500 and id kick myself if i had to replace them...

Edited by mass_iv

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...