Jump to content
SAU Community

Recommended Posts

Hi again, Just fitted the Bee-r to my R34 GTT (as posted the other day) and all was running fine, infact it was running awsome , until it decided to die on me on the way home. I got it all set up and wired in properley and had the limit set to 7000rpm which is low to what i normally run at 8000rpm .On my drive home i never even hit the limiter and my car just died. I've removed the bee-r and it still wont start or run. I've done a few checks, spark plugs or o.k , compression test was fine , everything seems ok , but i now have no spark to the plugs. Also i can hear a buzzing noise coming from the idle control valve when i turn on the ignition , is this supposed to happen as i dont recall hearing it before. I've took the covers off my power FC and nothing is fried in the ecu either so just wondered if anyone has any ideas

many thanks

Link to comment
https://www.sau.com.au/forums/topic/188968-r34-gtt-having-problems/
Share on other sites

8000 rmp?

does it even make power that high? Standard block and head? cams?

What turbo are you running and at what psi?

Cant the PFC increase the rev limit to 8000 without the bee-r?

Edited by silverr34gtt
8000 rmp?

does it even make power that high? Standard block and head? cams?

What turbo are you running and at what psi?

Cant the PFC increase the rev limit to 8000 without the bee-r?

ive posted some pics in the gallery section now.

Running a T70 at 22psi with external wastegate

Tomei pon cams

greddy inlet manifold

stainless topmount exhaust manifold

full 3 1/2 inch exhaust custom built straight through from turbo back with Nurspec backbox (no cat)

150 wizard of noz system with spray and purge

I did all the work/fabrication myself with just a bit of time and patience

Edited by GTmike34

Will it even crank? Or is it, turn key, buzz noise? I'd recheck the fuses in the kick-panel, my old GT used to mysteriously blow one of the main fuses giving the exact same symptoms.

Sometimes the fuses blow so neatly you can't see the break.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...