Jump to content
SAU Community

Recommended Posts

Been reading for years that the N1 pump just has a higher rated spring over the standard pump

I just read this

www.gtr.co.uk/forum/upload/39978-n1-oil-punp-upgrade.html+N1+oil+pump&hl=en&ct=clnk&cd=5&gl=us

is this true? Or did this person pick up a Nismo pump rather an N1?

thanks!

Link to comment
https://www.sau.com.au/forums/topic/189044-n1-oil-pump-flow-more-than-factory/
Share on other sites

n1 oil pump pumps around 25% more oil than standard. theyre a high flowing oil pump.

if you're using one on a high revving engine make sure you do the oil feed mod to your block as it can empty your entire sump 25% quicker :cool:

high pressure pumps increase oil pressure throughout the rev range.

you can make any oil pump have a harder spring, just tighten the big bolt on it. all this does is raises or lowers the peak oil pressure.

it works on the same principal a wastegate works on.

  • 2 weeks later...

I was under the impression N1 oil pumps flow "LESS" than factory ones.

they are designed for constant hi revs.

and being that the RB's all have oil control problems, where by too much oil gets pushed to the head, the N1 designed for that sort of situation flows LESS.

Same goes for the N1 water pumps compared to other RB water pumps.

thats true but only for the N1 water pumps. they flow less at low rpm because they were designed mainly for vehicles that are track dedicated or vehicles that are driven hard (sustain high revs, often) and are fed a higher volume of water at higher rpm where they spend most of their time.

N1 oil pumps flow more all over the rev range. they are a 'high volume' pump which means more oil and higher pressures. i've got one in my car and my std gauge reads a little higher than what it used to before the build.

Well the thing is I've always *read* the n1 pump just has a higher rated spring. I've never came across something otherwise until recently. Even sydneykid said so himself

http://www.skylinesaustralia.com/forums/in...t&p=1668325

Higher pressure doesn't substaniated higher volume. You can have higher pressure with the same volume.

Edited by maximajim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...