Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm clearing out some of the larger bits and pieces from my garage as they are taking up too much space.

Stock stuff

Bonnet sold

R32GTSt driver side front guard, gunmetal, straight, paint in good condition with a few minor blemishes and light scratches. compliance indicators are still installed $75

post-2863-1192318735_thumb.jpg

R32GTSt passenger side front guard, gunmetal, slight kink where the tyre nicked the guard at a skid pan day but barely noticeable, paint ok, compliance indicators still installed $65

post-2863-1192318792_thumb.jpg

R32GTSt stock rims with shot tyres. I think they are in reasonable condition, there's almost certainly some gutter rash but i haven't looked closely in the last few years since they were taken off. $200 for the 4

post-2863-1192318901_thumb.jpgpost-2863-1192318958_thumb.jpg

R33GTSt front half of the manual tail shaft, i got it to pinch the yoke for my gear box swap, ended up getting a new one. $25.

Performance stuff

M's K&N pod. One of the big ones including the adapter to bolt to the stock afm. Also fits z32 afm. used. looks to be in reasonable condition $50

post-2863-1192282101_thumb.jpg

X Force 3.5 inch straight through cannon. Universal fit, brand new, never used (the plug has been used as it fit my current exhaust) $100

post-2863-1192282240_thumb.jpg

I'll post some more pics up tomorrow when the light is better.

All prices ono. Pick up only at Campbelltown NSW for the stock stuff as it's just too big/heavy/easily damaged for postage. pod can be posted at buyers expense.

Thats all i can think of atm

cheers

Dave

post-2863-1192318629_thumb.jpg

Edited by BHDave
Link to comment
https://www.sau.com.au/forums/topic/189164-r32gtst-bonnet-guards-rims-ms-pod/
Share on other sites

pics added.

Dave, 2 of the wheels have no rash and are in surprisingly good condition, one has a very small mark on the lip and one has a bit of rash (i've added a photo of the rash).

cheers

Dave

i will have in a week or so, just waiting on my gtr ones to arrive. The top mount has snapped off where the screw goes through but i've just had a big washer on there holding it in place for the last 3 years with no problem

Where abouts in sydney do you live becuase i'll take that bonnet asap, if you could drop it off to my house i would be happy to pay $200, i am located near North Richmond, thanks

sorry whyte, the r32 and r33 front halfs are completely different. The r32 has the center bearing on the front half and the r33 has it on the back half from memory (or vice versa). The yoke size is different as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...