Jump to content
SAU Community

Recommended Posts

Hey guys n gurls,

Ive got myself a blitz SBC i-d III and struggling to get it to work correctly, ive wasted $50 in fuel trying to get it to boost over 9psi!!

Ive got no idea why it is not boosting to a 10psi level which ive consistantly set it for?! It ussually hits 7.6psi - 7.8psi then if I turn off the controller it hits a nice 8.9psi by itself!! Im so very confused why this is happening??

Was I meant to remove anything to let it boost higher than stock?

If anyone can help out would be greatly appreciated! Yes ive checked for leaks, and yes the boost lines are designed for boost and not stretching a great deal under presure?!

Help me!! Thanks.

Link to comment
https://www.sau.com.au/forums/topic/189753-blitz-sbc-not-reaching-set-boost/
Share on other sites

Have you got it on Auto or Manual mode?

Try moving the gain up a little, I think standard it is 5, it can go a lot higher, but it is sensitive, move by 2 at a time. If it doesn't change anything by 10 then I'd look at your plumbing. Try using manual and setting the gain to 8 - 10 then moving the level or whatever it's called up to 60 or 65. Only move in small steps.

I trust you have completely removed the plumbing from the original boost controller?

I use Manual. Setting = Level 60, gain = 6.

Auto set to 10psi, usually boosts to 9.8 or so, but not as quickly as manual mode.

intake is colder when your car is hence why it boosts harder.

Even in auto set at about 12psi the stupid thing wont boost past 9psi.

I will give the manual setting a go again, however I can reach 9psi with a setting of 7 Gain and 17ratio, go figure?!

I think it must be the length of my plumbing, its mounted in my air box (solanoid that is) so I guess the trail back to the controller is a lil far but I didnt think it would cause it a problem?!

May I add it only hits 9psi on top speed run 140km/h for eg.. and 8.9 turned off just in 1-2-3rd? to about 80km/h??

Edited by DECIM8

My stock boost sensor was still connected, when I removed it then engine light came on like its meant to when you install these little buggers, perhaps this was skipped?? because we were expecting it to light up :S

Will it be ok with the sensor removed? gauges still work which is found interesting.

Edited by DECIM8

Firstly I have an R33.

I already had a manual bleed valve fitted which was not plumbed into my factory boost controller. So although the solenoid id still electronically connected it is not plumbed into any piping. My twin solenoids from Blitz are mounted on the strut tower next to the factory one using one of those bolts on that bracket. Then it uses the stock plumbing points (R34 intercooler) for the solenoid, with the one going to the original blocked off.

The boost on the dash on the R33 is read from the back of the plenum to a electronic boost sensor near the brake cylinder. So it will read even when the solenoid is disconnected.

My idea is to raise the ratio to 40 or 50, with gain at 6 or 7.

Using manual .. I pull hardest for some strange reason when im setting it at about 17 ratio and 6-7 gain which I find rather strange for people pulling a good 60ratio like above!!

Its just not working for me .. its like the stock system is still running .. maybe its been installed incorrectly.

Using manual .. I pull hardest for some strange reason when im setting it at about 17 ratio and 6-7 gain which I find rather strange for people pulling a good 60ratio like above!!

Its just not working for me .. its like the stock system is still running .. maybe its been installed incorrectly.

hmm, that doesnt sound right i run around 60/70 ratio for 16psi but i am running a largeish aftermarket turbo. also the more gain you use the quicker/harder the boost will come in but the more likly it is to spike

  • 2 weeks later...

Yeah I worked it out mate, the wire had been frayed snapped by the last asshole who sold it to me (G.A Garage) dont buy anything from him btw.. fixed and now boosting hard...

Thanks for all the help

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...