Jump to content
SAU Community

Recommended Posts

went to a test n tune last friday nite at benaraby

best time managed was 13.318 @ 107.6mph (i thought a stock 33 with cooler/exhaust/ecu would get 108-110mph) hmmm

60ft was 2.2sec

car was on dyno weekend b4 made just a tiny bit over 300rwhp

car only hit 16.5psi all nite, i was hoping for over 110mph, maybe i should have dialed in a few more psi..

my mph seems down for my power? anyone?

Edited by l0WRB
Link to comment
https://www.sau.com.au/forums/topic/190512-test-n-tune-mph-vs-hp/
Share on other sites

Should be around 110-111, thats what i was running with 220rwkw.

And being a stock turbo wont really make 220rwkw in the real world... Your MPH is right for the power of 200rwkw, which is what the stock turbo makes

(270-275rwhp)

MPH isnt down for the power, its just showing your reading was probably a little inflated.

im running kkr480 with link ecu and 600cc injectors dude,

only rolled up 300hp cause intake temps to hot and tuner said he has knock control on and as he added timing link would pull it back out like 6 degrees at a time, i know my hp is down, but dyno readout is on a very old dyno, known to read low and has never been calibrated in the god know how many yrs its been there lol

my mates r32 came up with me, he ran up 13.4 @ 116mph

mind u traction was a joke, track had dirt and rocks all over it.. hmmm

but like u said i was expecting around 110-111mph which is wot i was thinkin hmmm

Edited by l0WRB
Should be around 110-111, thats what i was running with 220rwkw.

And being a stock turbo wont really make 220rwkw in the real world... Your MPH is right for the power of 200rwkw, which is what the stock turbo makes

(270-275rwhp)

MPH isnt down for the power, its just showing your reading was probably a little inflated.

i raced 2 skylines there on the nite, a silver 33 with cooler exhaust etc and a r34 with same mods and i absolutely smashed them specially thru top end

so i dunno wot the go is hey grrr

my mate who ran 116mph he was hitting limiter in 4th going over the line, and last time it seen dyno it was around the 400rwhp mark

Hehe that would be my 34. its got cat back. thats the only mods it has. i was doing 2.6 60fts... couldnt get any traction or it would bog.

i ran 93mph dude and thats holding 6psi boost. just to give an indication

the r33 was running a garrett gt3017r i think, front mount, zorst, boosted to around 8-9psi i think. he was pretty dissapointed i think.

But yeh im dead stocko to be honest matey i was expecting to get wasted hehe. love how low your car is. plates definitely apply

Edited by Granthem
Hehe that would be my 34. its got cat back. thats the only mods it has. i was doing 2.6 60fts... couldnt get any traction or it would bog.

i ran 93mph dude and thats holding 6psi boost. just to give an indication

the r33 was running a garrett gt3017r i think, front mount, zorst, boosted to around 8-9psi i think. he was pretty dissapointed i think.

But yeh im dead stocko to be honest matey i was expecting to get wasted hehe. love how low your car is. plates definitely apply

haha awsome man, your car still went alrite lol yeh i would launch at about 4000rpm and it would just bog and then lagg lagg then boost haha..

me and a mate were both racing my car, yeah that r33 went alrite then i would just reel him in top end... where r u guys from? gladstone?

Edited by l0WRB
haha awsome man, your car still went alrite lol yeh i would launch at about 4000rpm and it would just bog and then lagg lagg then boost haha..

me and a mate were both racing my car, yeah that r33 went alrite then i would just reel him in top end... where r u guys from? gladstone?

we are from rocky. Im generally there most meets with either my commie or the r34 now days.

My coil overs led to bad wheelspin. abit hard i think lol. Could spin all first after a bog down and coming back on boost, then all second, chirp 3rd and chirp 4th over the line. dunno how it did it haha stocko clutch wasnt expecting it to hook up so well!

yeh its a base figure. my times were terrible but due to the launches. but im just aiming for 100mph with a full zorst and up the boost to 12psi. close to 100mph anyway. and hopefully a high 13 with a good launch.

Edited by Granthem
i raced 2 skylines there on the nite, a silver 33 with cooler exhaust etc and a r34 with same mods and i absolutely smashed them specially thru top end

so i dunno wot the go is hey grrr

my mate who ran 116mph he was hitting limiter in 4th going over the line, and last time it seen dyno it was around the 400rwhp mark

limiter in 4th at only 116mph doesnt seem right. whats his limiter set at? must be only like 6000rpm?

Some answers;

Was the dyno run for power done with the bonnet up?

Do you have a pod filter without a heat sheild?

If the answer is yes to both I think you are experiencing less power on the road/track then you see on the dyno.

Also the KKr turbo's tend to suffer a little from lag, resulting in lower average power. Average power is king not peak power. Robo's HKS equiped car with 300rwhp would have had a notably fatter power band than your KKR making the average power higher and the car faster over the 1/4 mile (with a higher terminal).

For comparison my 175rwkw r33gtst ran 13.3 @106mph on a fairly hot day with a 2.3 60ft. Stock intercooler/turbo(10psi) and ecu with S-afc.

With a stock ecu and that turbo you might be asking for trouble given the timing map would be unsuited to the KKR curve. Probably worth getting a S-AFC or an ecu upgrade soon.

Some answers;

Was the dyno run for power done with the bonnet up?

Do you have a pod filter without a heat sheild?

If the answer is yes to both I think you are experiencing less power on the road/track then you see on the dyno.

Also the KKr turbo's tend to suffer a little from lag, resulting in lower average power. Average power is king not peak power. Robo's HKS equiped car with 300rwhp would have had a notably fatter power band than your KKR making the average power higher and the car faster over the 1/4 mile (with a higher terminal).

For comparison my 175rwkw r33gtst ran 13.3 @106mph on a fairly hot day with a 2.3 60ft. Stock intercooler/turbo(10psi) and ecu with S-afc.

With a stock ecu and that turbo you might be asking for trouble given the timing map would be unsuited to the KKR curve. Probably worth getting a S-AFC or an ecu upgrade soon.

its running a full replacement ecu already LINK ecu.

i think i need to get car redone by a person who knows link a bit better i think. hmmmm

its running a full replacement ecu already LINK ecu.

i think i need to get car redone by a person who knows link a bit better i think. hmmmm

Maybe not.

There could be other issues, like a blocked cat.

Do you have a dyno with AFR's to post up at all?

Maybe not.

There could be other issues, like a blocked cat.

Do you have a dyno with AFR's to post up at all?

speaking about cats,

about 2 weeks ago i pulled my gutted 3" cat off and put a stock 3" cat back on that i bought from a member from sau..

only done it 2 try and quieting down the exhaust as its loud as.. but hmmm

no sorry i dont have a dyno printout with afr's, but i can asure u its gettin clean afr's

tuner only added around 5 degrees timing over standard,not sure how it works but thats wot was told to me wen i was watchin him, but link would pull out timing as soon as it gets 2 much knock.

Edited by l0WRB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...