Jump to content
SAU Community

Recommended Posts

I just used 2 female insulated terminals. They push on nice and tight and do the job just right. You can pick up some terminals at a repco or auto sparkys for a bout $3 or less.

Here's my install.

http://www.skylinesaustralia.com/forums/t1...87#entry3337787

You'll need a crimper. I also just cut the bottom of the bracket off so the pump fits easier. I stripped the wire back and soldered the wire before I crimped onto them too.

You need some more hose to reach the pump as well.

I used the extra hose and cut it up and used it as mounts to prevent excess noise. And just tightened up on them and the pump with 25mm-50mm hose clamps.

Edited by KeyMaker
out of curiosity, whats the walbro good for at 13.8 volts in terms of rwkw?

cats car had no issues making over 300rwkw with it. The car now runs a tomei pump but the only reason i swapped the walbro out was because it was nearly 2 years old... i have no doubt it would have continued on no dramas

cats car had no issues making over 300rwkw with it. The car now runs a tomei pump but the only reason i swapped the walbro out was because it was nearly 2 years old... i have no doubt it would have continued on no dramas

Is that the exact same one that SLIDE sell's, or a different version?

Apparently there is 2 different versions, ones a high flow (HF) pump someone mentioned?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...