Jump to content
SAU Community

Recommended Posts

pretty fkd up

me and alot of mates from skool went to our skool tonight coz its muck up day tomorrow

security guard called cops n they came n chased us

few of us got away but then got phone calls saying to come back other wise we are getting expelled and locked up so we did

got made to lie on the floor and cops were being biggest fk heads

one of em kicked my mate and one got in my face and asked me if i thought it was fkn funny...i said no lol

any who got put in a patty wagon and got taken to the station on wakefield st.

i rang my sis to come get me.

the fkd thing is the ones who g ot caught are the ones who did nothing and the ones who actually did shit got away some how.

cops are the biggest wanks saying were gonna go to juvy for 6 years and shit

well got skool tomorrow (actually today seeing its 1 30 am) hope dnt get in to much sh*t at school wish me luck lol..and yes i know shouldnt of been there but hey you learn by your mistakes

ay.

just thought i'd let yas know.

Link to comment
https://www.sau.com.au/forums/topic/190811-arrested/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

lmfao.

I'm with Dan on this.. Situation surrounding as if you go back. hahah. :/

At least if there's a next time and you get asked why you ran or didn't go back you can share this wonderfull experience of people being kicked etc for no valid reason.

Well lesson learnt. :D

But what did you or others actually do?

Link to comment
https://www.sau.com.au/forums/topic/190811-arrested/#findComment-3435357
Share on other sites

yer fair enough the cops are ment to their job im not hating em for that but they didnt need to kick my mate and call us f*ck heads and shit.

Only reason we whent back is coz my mate got a call and it was a mate who had got caught n the cops were saying to get back other wise we'll get expelled n get locked up...but the only way they would of known that we were out there is if someone who got caught ratted us out...which pisses me off.

well im off to school probs gonna get an ear full from the principal :D

its gonna be a good day :/

i'll keep u guys informed on what goes on today at school lol

Link to comment
https://www.sau.com.au/forums/topic/190811-arrested/#findComment-3435360
Share on other sites

lmfao.

I'm with Dan on this.. Situation surrounding as if you go back. hahah. :D

At least if there's a next time and you get asked why you ran or didn't go back you can share this wonderfull experience of people being kicked etc for no valid reason.

Well lesson learnt. :D

But what did you or others actually do?

lol i know i wish i just sed fk it and ran home lol ahh well

apparently eggs were thrown and the coppers said they found spray cans but no one had spray cans :/

they'll probs trying to scare us while on their power trips lol as if we'd go to gaol for 6 years lol

well off to school i'll keep ya guys posted lol

catch ya

Link to comment
https://www.sau.com.au/forums/topic/190811-arrested/#findComment-3435372
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...