Jump to content
SAU Community

Recommended Posts

Hey guys,

Im thinking of putting some Volk GTCs on my R33 gtst but am stuck for offset sizes. If anyone has gone down this road can you please post up a pic or recommend me some wheel sizes! cheers

-Dragonforce

PS: any pics of GTC's on gtsts would help me heaps to!

vlk-gtc.jpg

Edited by Dragonforce
Link to comment
https://www.sau.com.au/forums/topic/190911-volk-gt-cs/
Share on other sites

cant help you with pics but i must say, probly the best looking 33 i've ever seen was a clean stock series two dumped on gold GTC's

what colour is your car, what colour rims are you getting?

Mines a clean white series 2 with gold GTC's :)

I don't have pics yet with the rims on as i only chucked them on the other week but they look great.

Just so you know, i had to change all of my wheel studs to much longer ones to fit the rims on, this was an incredible pain in the ass!! Factor in around $140-$200 on 20 long wheel studs depending on where you get them from.

Link to comment
https://www.sau.com.au/forums/topic/190911-volk-gt-cs/#findComment-3441942
Share on other sites

  • 2 weeks later...
Ahh you guys are legends with the pics!

My car is a white Series 2. Was looking into getting silver wheels, Not really sure how flared gaurds will look on my car tho..

Don't flare the guards, it will look crap unless it's done really well by someone that knows what they are doing. But yeah the rims will look really good man :worship:

Edited by PM-R33
Link to comment
https://www.sau.com.au/forums/topic/190911-volk-gt-cs/#findComment-3462438
Share on other sites

I had a set of 18 x 8 +30 all round on mine. I personally think more dish and if it was lowered a little lower they would have looked nicer... but at the same time i was happy with it :P

http://www.skylinesaustralia.com/forums/in...g&id=122257

http://www.skylinesaustralia.com/forums/in...g&id=122258

http://www.skylinesaustralia.com/forums/in...g&id=122261

Link to comment
https://www.sau.com.au/forums/topic/190911-volk-gt-cs/#findComment-3471799
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You've got yourself a good old game of have fun. That shit is annoying as hell to remove. Thankfully for you, yours is on metal, most of the stuff I take it off is plastic, so typically hear guns are out. I normally end up continually dragging my thumb with pressure over it to get it to peel up. Eucalyptus oil then works well for getting residue and last remnants off.   Edit: plastic scraper might be worth while too. One that'll dig into the foam tape, but not scratch the paint.
    • So I ride and race motorcycles for fun and have always used a van to transport my track weapons. Figured towing a racebike with a skyline would be different and if done right could - "look fully sik" or quite cool for us grown ups lol. Pic of yours truly on two wheels I also have a trailer already kitted out to transport my bikes ...and I have a spare set of rims that match the car that I was going to rebarrel to get deeper dish at some stage but they have just been gathering dust. Sooooooo it is only logical.... Stay tuned !!    
    • If by "flap disc" you meant "chocolate wheel".... then they are OK for getting off stubborn remnants. But not for stuff with bulk depth. If by "flap disc" you meant "abrasive paint f**ker"....
    • Beauty, thanks guys, got some ideas now. I note that none of you agreed with the flap disc so that's good to know. 👌🏻
    • I had small pin holes in my glazing putty but didn't want to put more putty to not make a mess again and I put 2 coats of epoxy primer to prevent it from rust. Though you can only see the pin holes if your eyes are almost against the panel. Do you think when the 3x coats of high fill 2k primer and 2 base coats go on that it will be visible? 
×
×
  • Create New...