Jump to content
SAU Community

Recommended Posts

Hey guys and gals, i've just recently joined the the forums, and I'd like to introduce myself. My name is Roald, but you can all call me Roo.... its easier :)

Now, I don't drive a skyline, but i do have a RB30DET (25/30) in my VL Calais, and I figured this would be a good place to get some good info on the newer nissan tech, as the VL sites i've become accustom to are more 'SOHC oriented'....

I have some Q's regarding my setup etc. but I'll get to them at a later date (studying....)

Looking forward to getting involved,

Regards, Roo ;)

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/
Share on other sites

  • 4 weeks later...

Ok, so its been a while.... I've been busy finishing my CIT course - flat out!

Here are some pics and info from the prevoius owner. I would have loved to do the conversion myself, but this came along and was far more cost effective :)

Engine

7,000 km's old

3ltr, acid cleaned, crack tested

bored and honed 50 tho to suit oversized pistons,

shot peened rods. New mains, big ends, small ends, balanced etc.

genuine Nissan head gasket

reconditioned RB25DET cylinder head with extra provision for VCT,

ceramic T3 turbo driven only on 6 psi

3inch exhaust with high flow cat

New bosch 910 fuel pump

Custom braided lines for turbo

Nizpro engine bay mounted intercooler

Wiring harness professionally modified to suit vl

Gearbox

R33 turbo 5speed manual box

Pulled down for inspection before fitting

Short shifter

Harness and speedo modified to suit vl

Heavy duty clutch,

shaved flywheel,

Fully balanced and modified drive shaft to suit r33 box

148RWkW and 530Nm on 6 PSI, std. R33 computer :)

Will get more pics up later on some time.

Cheers, Roo

post-43945-1196227870_thumb.jpg

post-43945-1196227880_thumb.jpg

post-43945-1196227887_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3502555
Share on other sites

148rwkw? :huh:

Are you sure that figure is correct? You should be making a lot more than that...

No offence intended.

None taken :) .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :) You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

post-43945-1196474552_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3507884
Share on other sites

None taken :P .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :( You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

If I may voice my opinion... :)

Well if you want to get the most from your engine set up (RB25 / 30DET) then I would suggest a fairly large low mount turbo such as a Garret GT30 / 82R, dont bother high flowing the one you have.

Im using a GT30 / 71R (slightly smaller than the 82R) and it is good for about 250rwkw, the larger GT30 / 82R will be better for your engine because you have more down low power because of the larger capacity and it will probably spool a larger turbo pretty quick.

If youre going for out right power then you will need a fuel pump - go for a Walbro in tank or Bosch 040. You'll also need to upsize your injectors as the standard ones will max out pretty quick, go for some SARD 550cc brand new squirters, dont bother having the standard ones high flowed.

As for your intercooler, I have been using a Just Jap / Cooling pro 300 x 600 x 76 front mount for a while and Ive never had a problem, I would highly recommend one for the price.

Get in contact with GCG in Sydney for the turbo, Powerflow injection for the pump and injectors and Just Jap for an intercooler.

Im using similar equipment in my RB25DET (550cc injectors, 040 pump, GT30 / 71R and JJR front mount) and my car makes 230rwkw and 550nm at 18psi, very conservative AFR and it has bugger all lag.

:D

post-17958-1196919715_thumb.jpg

Edited by Bullet32
Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3517303
Share on other sites

Great, thanks for the info :P

For the moment its on hold due to a matter of funds, but I will definitely take your advice into consideration. I have been considering dropping the whole lot into an R32, but again this is more likely to happen later rather than sooner, once I finish my apprenticeship :P

BTW, anyone know what a good R32 rolling shell might be worth, just out of curiosity?

Cheers, Roo

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3524527
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...