Jump to content
SAU Community

Recommended Posts

hi all. please need help afc neo settings . biggest problem i have is (thr settings. " no good" )

need folowing settings ( &&&)

R33 RB25det turbocharger KKR430, gtr intercooler.

warning settings.

thr settings

rpm settingsdec air settings ( i have non stock turbo) (turbocharger kkr430)

thr points (lo. hi)

rpm settings. neo1.neo2.neo3 ......etc

if you have any information about settings . thank you

Link to comment
https://www.sau.com.au/forums/topic/192674-r33-rb25det-afc-neo/
Share on other sites

throttle settings: cyl = 6 and arrow pointing diagonally up and right.

warning settings set to what level you want a warning to flash at. eg. air flow 95%.

everyones dec air settings are slightly different. the manual shows the step to take to set it up. on all the ones i've set up i've never used it.

because the neo has quite a few load points (16 if i remember correctly) just leave them at what they are. (or what your calling your rpm settings)

throttle hi and low points are up to you. up to what point do you think ou are under low throttle. and at what point do you think your on high throttle. a common one is low at 15% - 20% and high at 55% - 60%

but that should be all decided by the tuner. so they can get the best out of it.

throttle settings: cyl = 6 and arrow pointing diagonally up and right.

warning settings set to what level you want a warning to flash at. eg. air flow 95%.

everyones dec air settings are slightly different. the manual shows the step to take to set it up. on all the ones i've set up i've never used it.

because the neo has quite a few load points (16 if i remember correctly) just leave them at what they are. (or what your calling your rpm settings)

throttle hi and low points are up to you. up to what point do you think ou are under low throttle. and at what point do you think your on high throttle. a common one is low at 15% - 20% and high at 55% - 60%

but that should be all decided by the tuner. so they can get the best out of it.

and what about ? afc can't install thr settings.. "NG" position. whats wrong. what about wiring connections its ok i

i've never seen this. are you sure the throttle signal wire is hooked up? and to the correct wire?

hi . i fixed probmlem (NG) its ok. question again. )) if you now can afc neo change ignition map ( have problem over boost) so meny question ?)) we have no tuner here thats why>)) thank you again

hi . i fixed probmlem (NG) its ok. question again. )) if you now can afc neo change ignition map ( have problem over boost) so meny question ?)) we have no tuner here thats why>)) thank you again

no, it cant change ignition map.

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...