Jump to content
SAU Community

Recommended Posts

Well i just picked up my shiny new (for me) 97 gtst and was paying a fair bit of attention to the oil pressure gauge when driving it around today

at idle it sits just under the 4 and when pushing it a bit goes up to just over 6.

Is that normal and or safe?

also when warming it up if u give it a bit of gas the pressure just keeps rising till you back off, then slowly drops off again. is that normal?

Not sure what the norm is and would rather find out now rather then in a few weeks the hard way.

Thanks for your help

Link to comment
https://www.sau.com.au/forums/topic/192903-oil-pressure/
Share on other sites

I don't have a lot of faith in the factory oil pressure gauge but your readings sound normal.

I have an aftermarket gauge and it shows completely different readings to the factory one. I've had an electrical and a mechanical gauge both showing the same readings, so I'm pretty sure it's accurate.

When at normal operating temp. my oil pressure is about 30psi (~2 bar) at idle and about 80psi at 3000rpm, on the aftermarket gauge.

Don't take too much notice of the reading when the engine is cold as they will always be higher until your oil warms up and thins out a bit. And, yes it is also normal for oil pressure to rise and fall as the engine revs do.

Do an oil change so you know what you have in there ( I'd suggest a full synth 5 or 10W 40) and then relax, it all sounds normal.

Link to comment
https://www.sau.com.au/forums/topic/192903-oil-pressure/#findComment-3465867
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...