Jump to content
SAU Community

Recommended Posts

Got some New Bendix Pads fitted to the front of my ride about 3 months ago, by a reputable business, which i will refrain from naming. I find that these pads squel a hell of a lot, to the point where it has become irratating. and they spew huge amounts of brake Dust, by the end of the week my wheels are covered in this filth which is a pain to wash off everyweek.

Is anyone else experiencing this type of wear and noise with Bendix pads? as im really considering getting rid of them.

:P

Link to comment
https://www.sau.com.au/forums/topic/193476-bendix-pads-and-brake-dust/
Share on other sites

haven't tried the ultimates, heard that they're rotor eaters... i'm currently on ebc green which i think are pretty good but have new ferodo DS2500's waiting to go in which are supposed to be very good. bit pricey though, double what you'll pay for the ultimates but no comparison as far as braking performance goes.

i use bendix ultimates front and rear, i find that on occasions there is a bit of a squeal but thats nothing compared to the brake dust it leaves, within about 2-3 days my chrome rims are bleck :P

thanks for the feedback fellas. ill try to deal with the dust, and also get my hands on that no squeks stuff..

kinda funny short story. one of my auntie's saw my car about a month ago when my wheels were covered in brake dust. then two weeks after she came around again, when my wheels were clean. and she said " Wow.. love the new Mags you bought, they look great".. explaining to her that I've had them the whole time was funny...

end.

QFM HPX FTW! Better performance than Ultimates, whilst still being very low dust and rotor wear...

Where do you get them from and how much?

I have ultimates. They're pretty dirty pads, but like evil weevil I have black rims so it doesn't bother me. And squeal comes and goes, it squeals on rare occasions for me. It seems to be different from car to car as for the amount of squeal.

Overall I'm happy with them and their performance for a road car, even though they have their downsides, they were dirt cheap.

Edited by KeyMaker
Where do you get them from and how much?

$75. I'm a QFM Stockist (as well as Bendix, EBC, RDA, Ferodo, Protex etc.), and I'd take QFM over any of them...

PM me, or checkout www.gslrallysport.com if you're interested.

Edited by jetpilot1986
  • 3 weeks later...

I've been using Prime brake pads really cheap pad $90 all round, no dust problems no squeal problems and I give them a real bashing... was using ultimates at $200 all round, got sick of them real quick... and I honestly can't see these prime pads as being bad at all... They have been on for 3months, I must admit I haven't been driving as much but They seem fine...

cheap usually sucks... but not these, I didn't think they would be much chop but since they are only $90 for both front and rear I thought they are worth a go... very surprised, I wouldn't use them for track though I have another setup for those days, but do take them on rather harsh midnight runs...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...