Jump to content
SAU Community

Bendix Pads And Brake Dust

Gazzilla
 Share

Recommended Posts

Gazzilla Experienced

Gazzilla

Posted
Posted

Got some New Bendix Pads fitted to the front of my ride about 3 months ago, by a reputable business, which i will refrain from naming. I find that these pads squel a hell of a lot, to the point where it has become irratating. and they spew huge amounts of brake Dust, by the end of the week my wheels are covered in this filth which is a pain to wash off everyweek.

Is anyone else experiencing this type of wear and noise with Bendix pads? as im really considering getting rid of them.

:P

Link to comment
https://www.sau.com.au/forums/topic/193476-bendix-pads-and-brake-dust/
Share on other sites
Sandeep Community Regular

Sandeep

Posted
Posted

haven't tried the ultimates, heard that they're rotor eaters... i'm currently on ebc green which i think are pretty good but have new ferodo DS2500's waiting to go in which are supposed to be very good. bit pricey though, double what you'll pay for the ultimates but no comparison as far as braking performance goes.

Gazzilla Experienced

Gazzilla

Posted
  • Author
Posted
i use bendix ultimates front and rear, i find that on occasions there is a bit of a squeal but thats nothing compared to the brake dust it leaves, within about 2-3 days my chrome rims are bleck :P

thanks for the feedback fellas. ill try to deal with the dust, and also get my hands on that no squeks stuff..

kinda funny short story. one of my auntie's saw my car about a month ago when my wheels were covered in brake dust. then two weeks after she came around again, when my wheels were clean. and she said " Wow.. love the new Mags you bought, they look great".. explaining to her that I've had them the whole time was funny...

end.

RBwhatever Veteran

RBwhatever

Posted
Posted (edited)
QFM HPX FTW! Better performance than Ultimates, whilst still being very low dust and rotor wear...

Where do you get them from and how much?

I have ultimates. They're pretty dirty pads, but like evil weevil I have black rims so it doesn't bother me. And squeal comes and goes, it squeals on rare occasions for me. It seems to be different from car to car as for the amount of squeal.

Overall I'm happy with them and their performance for a road car, even though they have their downsides, they were dirt cheap.

Edited by KeyMaker
gslrallysport Experienced

gslrallysport

Posted
Posted (edited)
Where do you get them from and how much?

$75. I'm a QFM Stockist (as well as Bendix, EBC, RDA, Ferodo, Protex etc.), and I'd take QFM over any of them...

PM me, or checkout www.gslrallysport.com if you're interested.

Edited by jetpilot1986
  • 3 weeks later...
75coupe Grand Master

75coupe

Posted
Posted

I've been using Prime brake pads really cheap pad $90 all round, no dust problems no squeal problems and I give them a real bashing... was using ultimates at $200 all round, got sick of them real quick... and I honestly can't see these prime pads as being bad at all... They have been on for 3months, I must admit I haven't been driving as much but They seem fine...

cheap usually sucks... but not these, I didn't think they would be much chop but since they are only $90 for both front and rear I thought they are worth a go... very surprised, I wouldn't use them for track though I have another setup for those days, but do take them on rather harsh midnight runs...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...