Jump to content
SAU Community

Recommended Posts

Hello all,

just wondered if any of you have heard of this. Whenever I acclerate at low speed, I hear a loud click, coming from outisde (or underneath) the car. It also happens when i stop accelerating.

Could it be that the center bearing is stuffed? Seems to happen when there is an intial change rpm?

Any thoughts are welcome.

Cheers,

Eek:alien:

Link to comment
https://www.sau.com.au/forums/topic/19353-loud-clicking-noise/
Share on other sites

mine does this too, the clicking isn't that loud though.

and it's only a single click when accelerating at low speed or, the transition to de-acceleration at low speed. sounds like your car has the same problem though.. it's a bit annoying, i too am interested to know what it could be, as i want to get it fixed soon, when i do my 80,000km service

  • 1 year later...

IRS? As in the boot around the steering arm? If thats what you mean then no. I had a laser before that had that and it would make mechanical clicking noise when turning. Its completely different in the skyline. Its more electrical, like a relay.

The 32's have a common problem with the brakes making noises. Get someone to stand beside the car (crouched down) when you take off and see if they can hear it.

It could be the pad taking up free play in the caliper.

It could also be a universal joint in the tailshaft as these make a crack when you accell and then come off accell.

Rear driveshaft's in those are pretty strong and seeing as though they don't turn too much then I doubt this will be your problem (don't rule it out though)

I would check brakes then check tailshaft.

You could remove the rear pads temporarily to see if it still does it.

With the tailshaft it will make a loud ping when you apply/remove torque. (like banging your tailshaft with a small hammer)

Hey Igor,

if you think you're going nuts... I was about to type up a reply saying that I have heard a similar clicking coming through the passenger window, sounding like something metal stuck on my tyre, then I remembered that just this afternoon, we found a nail stuck in my front left tyre...

Before I was laughing because i'm going loopy, now i'm just thinking about the time and money it'll cost to get sorted out... dammit..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...