Jump to content
SAU Community

Recommended Posts

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 weeks later...
Originally posted by West

This prick sell parts for our lines( second hand ), my mate bought a set of coil over for his line . After trade his stock shocks and spring in we found out that his rear pair coil over was for driff only and they were all **** so we went back and ask to return it and get our stock supspension back ( me mate paid $500 for the coil over )...

This prick reckon our stock supspension was **** and he threw it out ( there were nothing wrong with our supspension ) and now if we want to return the coil over we need to purchase a stock set off him.

So me mate had no choice but to agree and he replaced his **** coil over with a set of stock supspension for me mate.

We we pick our car up i test drove it and found out that this set was even worse than my mate old stock supspension.

So if anyone want this prick name, pm me for it because i think we don't need prick like this in our society and this prick operate his business around STH EASTERN area .:P

Dude you're to have a negative trader rating of your own soon.

Those guages that I sent you that have been sitting at the Post Office for the last few weeks, so can you please go and pick them up.

And please reply to your PM's. :)

I told you i just had a defect didn't i? You think its' easy to fix a defect these day? Put you in my situation, what would you do? Fix your car to go to work or pick up some gauges? Shit happens alright! ( i think i did mention that i'll pick it up next week too )

West yeh mate you did tell me you got a defect, and yeah you did mention you'd pick them up last week. All I ask if for you to honour your half of the deal. But remember dude the PO won't hold them for ever and I'll be stuck with the postage bill.

R34-GTT yeah dude I COD'd them.

Oh and you ask what would I do if I were in your shoes ... I would at least have the common courtesy to write back to Private Messages and explain what is going on, rather than giving replies such as "Problem with post.".

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...