Jump to content
SAU Community

Recommended Posts

got an r34 auto that planning to get a stage 2 shift kit. just curious if anyone knows where i can get one installed in melb. or if theres anyplace that is willing to order one from mv in adelaide and install it for me. cheers

Edited by john-e boi

i had my valve body modified by MV auto aswell.

i took my car to J&P Clayton Automatics where they removed, packed and shipped the unit to adelaide.

and then MV shipped it back to J&P to have refitted to my car. total turnaround was exactly a week.

the guys at J&P were pretty good. i'd definitely go back there again if i needed anything.... so give them a try.

29 Garden Rd, Clayton. T: 9574 1140

i had my valve body modified by MV auto aswell.

i took my car to J&P Clayton Automatics where they removed, packed and shipped the unit to adelaide.

and then MV shipped it back to J&P to have refitted to my car. total turnaround was exactly a week.

the guys at J&P were pretty good. i'd definitely go back there again if i needed anything.... so give them a try.

29 Garden Rd, Clayton. T: 9574 1140

thanks for that. so was your car off the road for a week? left your car there? how much was it all up?

thanks for that. so was your car off the road for a week? left your car there? how much was it all up?

yep, car was off the road for a whole week.

well...

MV Auto shift kit (incl shipping to and from Adelaide) $384

"Davies Craig" oil cooler $117

J&P Auto's - Remove/replace valve body, service of transmission (incl flush oil, new filter + gasket), and fitting the oil cooler $346

as mentioned above, check the other section of the forums as this has been discussed in alot of detail - but definitely get the service done aswell, and if u wanna play it safe get an oil cooler for the transmission oil aswell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...