Jump to content
SAU Community

Centre Locking

subie

By subie,
in General Maintenance

 Share

Recommended Posts

grandmasterb Grand Master

grandmasterb

Posted
Posted
Hi,

just wondering, r32 come with centre locking? my r32 doesn't or not working! how can i check it?

cheers

Generally they do have central locking controlled from the drivers door but not keyless entry.

You can add a slave in the passenger's door so you have keyless entry if you wish.

If you lock the drivers door and the passengers door locks then you have central locking, if it doesn't then you dont have it/it is broken.

Pull the door skin off the drivers door and see if you can spot the actuator, if its there then its faulty/broken so will need replacing :verymad:

Link to comment
https://www.sau.com.au/forums/topic/194563-centre-locking/#findComment-3487525
Share on other sites
subie Grand Master

subie

Posted
  • Author
Posted
Generally they do have central locking controlled from the drivers door but not keyless entry.

You can add a slave in the passenger's door so you have keyless entry if you wish.

If you lock the drivers door and the passengers door locks then you have central locking, if it doesn't then you dont have it/it is broken.

Pull the door skin off the drivers door and see if you can spot the actuator, if its there then its faulty/broken so will need replacing :)

thanks mate,

I took the door panel off both sides, the driver door has actuator but the passenger door does NOT have it! there have the wiring with the plug hanging around where the actuator suppose to be.. How can i test it if that wire is for the actuator for centre locking? does centre locking has fuse? and where ?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/194563-centre-locking/#findComment-3489401
Share on other sites
GeeTR Grand Master

GeeTR

Posted
Posted
There have the wiring with the plug hanging around where the actuator suppose to be.. How can i test it if that wire is for the actuator for centre locking?...

Maybe you could tell with a test light, or multimeter in the plug end. Activate the central, and see if you get a signal out of the plug.

Link to comment
https://www.sau.com.au/forums/topic/194563-centre-locking/#findComment-3498955
Share on other sites
subie Grand Master

subie

Posted
  • Author
Posted
Maybe you could tell with a test light, or multimeter in the plug end. Activate the central, and see if you get a signal out of the plug.

no. i do get any signal from the plug.. where else should i check then? are there suppose to have any motor or actuator in the door for centre locking?

cheers

Link to comment
https://www.sau.com.au/forums/topic/194563-centre-locking/#findComment-3500965
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...